Radio Navigation · Chapter 5
Doppler Radar How the Doppler shift between a moving transmitter and receiver gives an aircraft its groundspeed and drift, with no help from the ground.
© 2026 eatpl.in. All rights reserved. For the personal study of eatpl.in students only. No part may be copied, reproduced, shared or distributed in any form without prior written permission. Unauthorised use may attract civil and criminal liability under the Copyright Act, 1957.
e-books by eatpl.in · © 2026 · Do not copy or distribute
A Doppler navigation system measures groundspeed and drift by measuring the Doppler shift of radar beams reflected from the ground. This chapter covers the Doppler principle and its arithmetic, then the airborne Janus array.
Chapter roadmap
What this chapter covers 01
What Doppler navigation is A self-contained system for groundspeed and drift, and its strengths and weaknesses.
02
The Doppler principle Relative motion shifts the frequency: fD = V ÷ λ.
03
Airborne Doppler Depression angle, the four-beam Janus array, frequencies and flight over the sea.
Chapter 5 · Doppler Radar
02
e-books by eatpl.in · © 2026 · Do not copy or distribute
Three parts: what a Doppler navigator does, the Doppler principle with its calculation, then how the airborne Janus array works.
Introduction
Groundspeed and drift with no ground aids Continuously measures the Doppler shift and converts it to groundspeed and drift Early systems: with heading and a start point, computed position (lat/long, distance to go, left/right of track) Modern systems blend Doppler with IRS, GPS, VOR/DME, Loran C to remove its errors The Doppler principle is also used in DVOR , VDF and some radars
Self-contained Needs no ground-based aids.
Worldwide Usable anywhere.
Best over land Most accurate overland.
Weaker over sea Waves, tides and currents move the surface; a smooth glassy sea may give no reading.
Chapter 5 · Doppler Radar
03
e-books by eatpl.in · © 2026 · Do not copy or distribute
A Doppler navigation system uses the Doppler principle to measure groundspeed and drift continuously. Early systems took a departure point, heading and the Doppler outputs and computed position. It is completely self-contained, usable worldwide and most accurate over land. Over the sea it is less accurate, because wind, tides and currents move the reflecting surface, and over a smooth, glassy sea it may fail to measure at all. Modern systems combine Doppler with IRS, GPS, VOR/DME and so on to cancel its errors, such as heading-reference error and loss of signal over water. The same principle is used in Doppler VOR, VDF and some radars.
01
The Doppler principle Relative motion between transmitter and receiver changes the received frequency.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Doppler principle
Relative motion shifts the frequency Whenever transmitter and receiver move relative to each other, the received frequency shifts in proportion to the rate of relative motion Closing: each wave arrives sooner, λ appears shorter, so f rises Opening: λ appears longer, so f falls The shift is the Doppler shift fD = fR − f ahead: bunched, higher f behind: stretched, lower f
Chapter 5 · Doppler Radar
05
e-books by eatpl.in · © 2026 · Do not copy or distribute
Whenever there is relative motion between a transmitter and a receiver, the received frequency changes in proportion to the rate of that motion. With both stationary the receiver gets f waves a second and there is no shift. If the receiver moves towards the transmitter, each wave arrives a little sooner: the wavelength seems shorter, and since c equals f lambda, the frequency seems higher. Moving apart, the wavelength seems longer and the frequency lower. The difference between received and transmitted frequency is the Doppler shift.
The Doppler formula
fD = V ÷ λ = V × f ÷ c V = relative speed in m/s ; λ in metres ; c = 3 × 10⁸ m/s Closing: received f = f + fD; opening: f − fD Knots to m/s: × 1852 ÷ 3600 (≈ ÷ 1.944); km/h to m/s: ÷ 3.6 Transmitter closing at 250 m/s, λ = 5 cm: fD = 250 ÷ 0.05 = 5000 Hz = 5 kHz
Receiver closing at 900 km/h on 6 GHz: V = 250 m/s; λ = 0.05 m; fD = 5 kHz
486 kt towards a 12 GHz beacon: V = 250 m/s; λ = 2.5 cm; fD = 10 kHz
Chapter 5 · Doppler Radar
06
e-books by eatpl.in · © 2026 · Do not copy or distribute
The shift equals the relative speed divided by the wavelength, or speed times frequency over the speed of light. Work in metres per second and metres. A transmitter closing at 250 metres per second on a 5 centimetre wavelength: 250 over 0.05 is 5000 hertz, 5 kilohertz. A receiver closing at 900 kilometres per hour on 6 gigahertz: 900 kilometres per hour is 250 metres per second, the wavelength is 5 centimetres, so again 5 kilohertz. And 486 knots is 250 metres per second; at 12 gigahertz the wavelength is 2.5 centimetres, so 10 kilohertz. Closing adds the shift to the transmitted frequency; opening subtracts it.
Transmitter and receiver combinations
Only the relative motion matters T R T moves towards R +fD (higher) T R R moves towards T +fD (higher) T R T moves away −fD (lower) T R R moves away −fD (lower)Exam: an apparent decrease in frequency occurs when the transmitter moves away from the receiver (or they move apart).
Chapter 5 · Doppler Radar
07
e-books by eatpl.in · © 2026 · Do not copy or distribute
It doesn't matter which one moves. Transmitter towards receiver, or receiver towards transmitter: positive shift, higher frequency. Either moving away: negative shift, lower frequency. A classic question: an apparent decrease in transmitted frequency, proportional to the transmitter's velocity, occurs when the transmitter moves away from the receiver.
02
Airborne Doppler Radar beams aimed at the ground, forward and aft, port and starboard.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Airborne Doppler
Beams aimed down at 60–70° Transmitter and receiver share one aerial but are screened from each other Beams sent to the surface at a depression angle of 60–70° ; the receiver measures the shift of the echoes Forward beams shift up , aft beams shift down , in proportion to groundspeed The angle is a compromise: near 90° the shift → 0; too shallow and the echo reflects away, too weak 60–70° forward beam: +fD aft beam: −fD
Chapter 5 · Doppler Radar
09
e-books by eatpl.in · © 2026 · Do not copy or distribute
In an airborne Doppler, transmitter and receiver share the aerial but are screened from each other. Beams go down to the surface at a depression angle of 60 to 70 degrees, and the receiver measures the shift in the reflected signal caused by the aircraft's speed along track and across it. The angle is a compromise: close to 90 degrees the beam is nearly at right angles to the motion and the shift approaches zero; too shallow and the energy strikes the surface at a grazing angle and reflects away, leaving weak, unmeasurable echoes.
Janus array
Four beams: groundspeed from fore and aft, drift from port and starboard Named after Janus, the Roman god who faced both ways Common: the four-beam X array Zero drift: both front beams shift up and both rear beams down, equally Drift: port and starboard shifts differ, converted to a drift readout Old systems rotated the aerial until port = starboard; drift = aerial angle from heading heading track fwd port fwd stbd aft port aft stbd drift 8° starboard: starboard beams' shift ≠ port beams' shift
Chapter 5 · Doppler Radar
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
Opposing beams form a Janus array, after the Roman god of doorways who faced both ways. A common one is the four-beam X. With no drift, flying forwards, the two front beams' echoes shift up and the two rear beams' shift down, equally, in proportion to groundspeed. With drift, the port and starboard beams see different shifts; modern fixed aerials convert that difference electronically into drift. Older mechanical systems rotated a pitch-stabilised aerial until port and starboard were equal: the aerial was then along the track, and drift was the angle between heading and aerial.
Frequency and the Janus advantage
SHF: 8.8 GHz or 13.3 GHz
Why SHF Higher frequency: more sensitive to the shift and narrower beams (1–5°) for a given aerial. Too high: absorption and reflection from precipitation. Compromise: 8800 MHz or 13 300 MHz .
Janus benefits Opposing beams cancel errors from small transmitter-frequency changes, pitch, roll and vertical speed .
Unlock Over an uneven or poor surface the system can unlock; it then goes to memory and stops computing groundspeed and drift.
Chapter 5 · Doppler Radar
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
The higher the frequency, the more sensitive the system to the shift and the narrower its beams, 1 to 5 degrees, for a given aerial size. Too high and precipitation absorbs and reflects the energy. So the allocated frequencies are 8800 or 13 300 megahertz, in the SHF band. The Janus arrangement also reduces errors from small variations in transmitted frequency, from pitch, roll and vertical speed changes. If the system unlocks, for example over an uneven surface, it reverts to memory and stops computing.
Example system
Four-beam Janus at 13.325 GHz Parameter Value Frequency 13.325 GHz Depression angle (beam centre) 67° Beam depth × width 5.6° × 11° Accuracy 0.3% of groundspeed and drift, 95% of the time
STBY Selected near structures and people: protects the equipment and people's health, and keeps it ready to transmit.
SEA Lights over water. Echoes from water are weaker at the front of the forward beams and rear of the aft beams (spillage), so groundspeed under-reads; the computer adds a correction.
Chapter 5 · Doppler Radar
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
A typical modern four-beam Janus system transmits on 13.325 gigahertz, with a depression angle of 67 degrees to the centre of each beam, beams 5.6 by 11 degrees, and an accuracy of 0.3 percent of groundspeed and drift on 95 percent of occasions. Its control unit has a standby setting for use near buildings and people, protecting them and the equipment. A SEA light comes on over water: echoes are weaker from the front of the forward beams and the back of the aft beams, so the measured shift, and therefore groundspeed, reads low; the computer compensates.
Summary
What to take into the exam What it gives Groundspeed and drift. Self-contained, worldwide, best over land.
The shift fD = V ÷ λ. Closing: higher. Opening: lower. Who moves doesn't matter.
Units V in m/s, λ in m. kt × 0.514 = m/s; km/h ÷ 3.6 = m/s.
Geometry Beams at 60–70° depression: a compromise between shift and echo strength.
Janus Fore/aft give groundspeed; port/starboard difference gives drift; cancels pitch/roll errors.
Weak spots SHF 8.8 or 13.3 GHz. Over sea: under-reads (SEA correction); glassy sea: may fail.
Chapter 5 · Doppler Radar
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
Six points: what Doppler navigation gives you and where it is weak; the formula and its sign; units; the 60 to 70 degree depression angle; how the Janus array gets groundspeed and drift and cancels pitch and roll; and the SHF frequencies and the sea problem.
Practice · Questions
Try these 1. A transmitter moves directly towards a receiver at 250 m/s on a wavelength of 5 cm. The frequency shift?
2. A stationary transmitter on 3 cm; a receiver moving directly away measures a 6 kHz shift. Its speed in m/s and knots?
3. An 8800 MHz transmitter moves directly away from a receiver at 291 kt. The shift, and the frequency received?
4. An aircraft flies at 486 kt directly towards a 12 GHz beacon. The change in frequency is: (a) 10 MHz (b) 6.25 Hz (c) 10 kHz (d) 6.25 kHz
5. An apparent decrease in frequency occurs when: (a) T and R move towards each other (b) T moves away from R (c) T moves towards R (d) both move away from each other
6. The shift of a radio transmission reflected from the ground is used to find: (a) drift and groundspeed (b) track and speed (c) crosswind and heading (d) track error and groundspeed
Chapter 5 · Doppler Radar
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
Six questions from the chapter and its question paper. Answers on the next slide; all the calculations can be done in the Doppler Lab.
Practice · Answers
Answers and working Q Answer Working 1 5 kHz 250 ÷ 0.05 = 5000 Hz 2 180 m/s, 350 kt V = fD × λ = 6000 × 0.03 3 4.4 kHz; 8799.9956 MHz 291 kt = 150 m/s; λ = 0.0341 m; 150 ÷ 0.0341; opening, so subtract 4 (c) 10 kHz 486 kt = 250 m/s; λ = 0.025 m 5 (b) Opening gives a lower received frequency 6 (a) Doppler gives drift and groundspeed
Chapter 5 · Doppler Radar
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
Question 3: 291 knots is 150 metres per second; at 8800 megahertz the wavelength is 3.41 centimetres; 150 divided by 0.0341 is about 4400 hertz. Moving apart, so the received frequency is 4.4 kilohertz lower: 8799.9956 megahertz. Question 5 is careful wording: (d) also gives a decrease, but the shift that's proportional to the transmitter's velocity is (b).
Try it yourself
Doppler Lab Watch wavefronts bunch up as the source moves Calculate any Doppler shift in m/s, knots or km/h Fly a four-beam Janus array with drift and see each beam's shift Exam questions ready to set up Open the Doppler Lab →
fD = V ÷ λ
Chapter 5 · Doppler Radar
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
The Doppler Lab animates a moving transmitter's wavefronts, calculates Doppler shifts in any units, and shows how the four Janus beams give groundspeed and drift.
eatpl.in · Radio Navigation · Chapter 5
Doppler Lab
Calculate any Doppler shift, watch the wavefronts, and see how a Janus array measures groundspeed and drift.
Doppler shift Janus array Practice
Questions from the chapter and its question paper. Set each one up, read the answer in the lab, then open the working.
E-book and lab by eatpl.in · © 2026 eatpl.in. For the personal study of eatpl.in students. Do not copy or distribute.