Radio Navigation · Chapter 9
Instrument Landing System Localiser, glide path and markers: how ILS guides an aircraft down to the runway, what the needles mean, and how low each category can go.
© 2026 eatpl.in. All rights reserved. For the personal study of eatpl.in students only. No part may be copied, reproduced, shared or distributed in any form without prior written permission. Unauthorised use may attract civil and criminal liability under the Copyright Act, 1957.
e-books by eatpl.in · © 2026 · Do not copy or distribute
ILS is still the most accurate approach and landing aid in everyday airline use. This chapter covers the components and frequencies, the markers, coverage, how the localiser and glide path work, the indications, the categories, the errors, and the 1 in 60 arithmetic.
Chapter roadmap
What this chapter covers 01
The system Components, frequencies, ident, markers, monitoring, coverage.
02
How it works Localiser and glide path lobes, DDM, false glide paths, back course.
03
In the cockpit CDI and HSI, dots and degrees, categories, errors.
04
Numbers Height and rate of descent by 1 in 60; the approach chart.
Chapter 9 · Instrument Landing System
02
e-books by eatpl.in · © 2026 · Do not copy or distribute
Four parts: the ground system, the principle, the cockpit indications and categories, and the arithmetic.
Introduction
Guidance in both planes, down to decision height The most accurate approach aid in regular airline use; allows autoland Localiser : lateral guidance along the extended centre lineGlide path : vertical guidance; both together make it a precision approach Fly the beams down to decision height (DH) At DH: visual references and room to land? Land ; if not, go around decision height go around land glide path (vertical) + localiser (lateral)
Chapter 9 · Instrument Landing System
03
e-books by eatpl.in · © 2026 · Do not copy or distribute
ILS gives pilots guidance in both the horizontal and the vertical plane, which is what makes it a precision approach; it even supports automatic landing. The localiser gives the extended centre line; the glide path gives the descent profile. The pilot follows them down to decision height. There, with the required visual references and room for a safe touchdown, he lands; otherwise he goes around and flies the published missed approach.
ILS in three dimensions
Two planes meet in one line: the approach LOCALISER: vertical plane (left / right) GLIDE PATH: plane tilted up 3° (up / down) where they meet = the approach path LLZ GP heights ×6
Chapter 9 · Instrument Landing System
04
e-books by eatpl.in · © 2026 · Do not copy or distribute
Picture ILS in three dimensions. The localiser defines a vertical plane standing along the extended centre line: it tells you left or right. The glide path defines a plane tilted up from the touchdown zone at about 3 degrees: it tells you up or down. Where the two planes intersect is a single line in space, the approach path, and that's what you fly down when both needles are centred. Heights are exaggerated six times so you can see the angle.
01
The system Three transmitters on the ground, paired frequencies, and lights in the cockpit.
e-books by eatpl.in · © 2026 · Do not copy or distribute
ILS components
Localiser, glide path, markers Localiser (VHF) Glide path (UHF) OM + locator MM IMLocaliser (LLZ) : VHF, about 300 m beyond the upwind end. Glide path (GP) : UHF, frequency paired, about 300 m in from the threshold, beside the runway at touchdown.
Markers : 75 MHz, OM, MM and maybe IM. A locator (L) NDB may share the OM site. A paired DME increasingly supplements or replaces the markers.
Chapter 9 · Instrument Landing System
06
e-books by eatpl.in · © 2026 · Do not copy or distribute
The ground installation has three parts. The localiser transmits in VHF from an aerial about 300 metres beyond the upwind end of the runway. The glide path transmits in UHF, frequency-paired with the localiser, from beside the runway about 300 metres in from the threshold, abeam the touchdown point. The marker beacons on 75 megahertz let the pilot cross-check height against range: an outer and middle marker, perhaps an inner. Many installations have a low-power NDB, a locator, at the outer marker, and a paired DME is increasingly used to supplement or replace the markers. Some countries also allow back course approaches.
ILS frequencies
Paired: one selection, one ident Part Band Frequencies Localiser VHF 108–111.975 MHz, 40 channels, odd first decimal Glide path UHF 329.15–335 MHz, 40 channels, paired Markers VHF all on 75 MHz (narrow vertical fans)
e.g. 108.1 ↔ 334.7 MHz; 111.95 ↔ 330.95 MHz. Pairing: one switch, less workload, fewer wrong selections, one ident.
108.0 109.0 110.0 111.0 111.9 ILS: odd first decimal (108.1, 108.15, 108.3…) VOR: even first decimal (108.0, 108.2…)
Chapter 9 · Instrument Landing System
07
e-books by eatpl.in · © 2026 · Do not copy or distribute
The localiser uses 108 to 111.975 megahertz, 40 channels, sharing the band with VOR: ILS frequencies have an odd first decimal, like 108.1 or 108.15. The glide path uses 329.15 to 335 megahertz, also 40 channels, each paired with a localiser frequency: 108.1 with 334.7, 111.95 with 330.95. Select the localiser and the glide path comes with it: one switch, less workload, quicker, fewer wrong selections, and only one identifier. All markers use 75 megahertz; their narrow vertical fans don't interfere.
DME and identification
Ranges from the threshold, ident on the localiser
Paired DME Supplements or replaces markers. Ranges are zero at the threshold . Protected within the localiser service area up to 25 000 ft ; wider if notified for SIDs and STARs.
Ident On the localiser: 2 or 3 letters , 7 groups a minute , usually starting with I . No separate GP ident.
Ident removed ILS unserviceable or withdrawn: ident suppressed . Maintenance or test: ident removed or a continuous tone . Don't use it.
Localiser only GP unserviceable: the ident still radiates; ATC will warn you. Don't use the glide path.
Chapter 9 · Instrument Landing System
08
e-books by eatpl.in · © 2026 · Do not copy or distribute
A DME paired with the ILS supplements or replaces the markers. Its ranges are zero-referenced to the threshold, and it's only protected within the localiser service area up to 25 000 feet, unless notified for SIDs and STARs. The ident is on the localiser only: 2 or 3 letters at 7 groups a minute, usually starting with I. When the ILS is unserviceable or withdrawn the ident is suppressed; during maintenance or testing it's removed or replaced by a continuous tone, and you mustn't use it. If only the glide path is out, the ident keeps radiating for localiser-only approaches; ATC will tell you.
Marker beacons
Lights and tones over the fans 75 MHz, fan shaped vertical beams; bone or lens shaped in plan Not directional: received only inside the fan Two required; a third (IM) where needed Back course markers need a distinguishable ident Z markers : cylindrical beam; mark airway points or an NDB's cone of silence OM · blue · 400 Hz MM · amber · 1300 Hz IM · white · 3000 Hz
Chapter 9 · Instrument Landing System
09
e-books by eatpl.in · © 2026 · Do not copy or distribute
Markers transmit on 75 megahertz in narrow vertical fans, bone or lens shaped from above. They're not directional: you only receive them inside the fan, and you get a light and a tone. The outer marker is blue, 400 hertz, two dashes a second, 6.5 to 11.1 kilometres out. The middle marker is amber, 1300 hertz, alternating dots and dashes, about 1050 metres out. The inner marker is white, 3000 hertz, six dots a second, 75 to 450 metres. Z markers have cylindrical patterns and mark airway points or the overhead of an NDB.
Ground monitoring
Automatic monitors switch it off if it drifts A monitor in an area of guaranteed reception acts when:
Fault Limit Localiser shift at the reference datum 35 ft Cat I · 25 ft Cat II · 20 ft Cat III Glide path angle change more than 0.075 × φ Power output falls more than 50%
It warns a control point, then, before a standby transmitter takes over:
Ceases all radiation or removes ident and navigation components or a Cat II/III ILS is downgraded to Cat I or II
Chapter 9 · Instrument Landing System
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
Both localiser and glide path are watched by monitors in an area of guaranteed reception. They act if the localiser at the reference datum shifts from the centre line by more than 35 feet for Cat I, 25 for Cat II, or 20 for Cat III; if the glide path angle changes by more than 0.075 times the basic angle; or if any transmitter's power falls by more than half. The monitor warns a control point and, before a standby transmitter takes over, either stops all radiation, removes the ident and navigation components, or downgrades a Cat II or III ILS to a lower category.
ILS coverage
How far, how wide, how high Coverage Localiser 25 nm within ±10°; 17 nm 10–35°; 10 nm beyond ±35° if providedGlide path 10 nm within ±8° ; vertically 0.45φ to 1.75φ (lower limit may be 0.3φ)
3° glide path: 1.35° to 5.25°. 3.5°: 1.575° to 6.125°. Outside coverage expect false courses and reverse sense on the localiser.
LOC 25 nm ±10° 17 nm ±35° GP 10 nm ±8°
Chapter 9 · Instrument Landing System
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
The localiser covers 25 miles within 10 degrees of the centre line, 17 miles between 10 and 35 degrees, and 10 miles beyond 35 degrees if coverage is provided there; the limits may be reduced where other aids cover the intermediate approach. The glide path covers 10 miles within 8 degrees either side, and vertically from 0.45 to 1.75 times the glide path angle, with the lower limit perhaps reduced to 0.3. For a 3 degree path that's 1.35 to 5.25 degrees; for 3.5, 1.575 to 6.125. Outside the coverage the localiser can give false on-course and reverse-sense indications.
02
How it works Two overlapping lobes in each plane; the needle shows which is stronger.
e-books by eatpl.in · © 2026 · Do not copy or distribute
The localiser
90 Hz left, 150 Hz right Two overlapping lobes along the approach, on one VHF frequency Seen from the approach: left lobe 90 Hz , right lobe 150 Hz Depth of modulation grows away from the centre lineDDM (difference) ∝ angle off: right of c/l, more 150 → fly left DDM zero = centre line = needle centred 90 Hz 150 Hz left / right as seen from the approach
Chapter 9 · Instrument Landing System
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
The localiser aerial produces two overlapping lobes along the approach on the one VHF frequency. To tell them apart the right-hand lobe, as you look along the approach, is modulated at 150 hertz, the left-hand at 90 hertz. The depth of modulation increases away from the centre line. Right of the centre line you receive more 150 than 90; the difference in depth of modulation, the DDM, is proportional to the angle off, and drives the vertical needle: fly left. Left of the line, more 90: fly right. Equal, DDM zero, you're on the centre line.
DDM
What the needle is really measuring Depth of 90 Hz and 150 Hz cross on the centre line The receiver compares them: the difference moves the needle Same idea for the glide path in the vertical The needle shows angle off, not distance: more sensitive closer in 90 Hz 150 Hz ← left of c/l: fly RIGHT right of c/l: fly LEFT → DDM = 0
Chapter 9 · Instrument Landing System
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
The receiver measures how deeply each tone modulates the carrier. On the centre line they're equal; move off and one grows as the other shrinks. The difference moves the needle. Because it's an angle, the same needle deflection means fewer metres off as you get closer to the runway.
The glide path
90 Hz above, 150 Hz below UHF; same principle with lobes in the vertical plane Upper lobe 90 Hz , lower lobe 150 Hz; glide path where DDM = 0Usually 3° ; ICAO allows 2° to 4° False glide paths from reflections and aerial height: always above , first at about 2φ (6°) Normally intercept from below ; check height against DME or markers 90 Hz above 150 Hz below false GP ≈ 6° heights ×6
Chapter 9 · Instrument Landing System
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
The glide path uses the same principle on a UHF carrier with the lobes in the vertical plane: the upper lobe at 90 hertz, the lower at 150. The glide path, usually 3 degrees and between 2 and 4 by ICAO rule, is where the DDM is zero. Reflections from structures and the ground, and the aerial's height, repeat the lobes and create false glide paths: always above the true one, the first at about twice the angle, 6 degrees. Normal practice is to establish on the localiser and intercept the glide path from below; where continuous descent approaches capture from above, always check height against DME or markers.
Back course, datum and PAPIs
Behind the localiser, and over the threshold LOC front course back course: CDI reversedBack course: not permitted in the UK . Glide path wrong (to the other end), CDI sense reversed , no markers. An HSI reads correctly if the front course QDM is set.
ILS reference datum About 50 ft above where the centre line meets the threshold: the glide path passes through it. In the AIP AD section.
PAPI Same angle as the ILS, but set for a mean eye height (MEHT), so the two differ slightly by aircraft.
Chapter 9 · Instrument Landing System
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
A mirror-image pattern radiates behind the localiser, the back course. Some countries use it for non-precision approaches; the UK doesn't, so ignore back course indications. Its disadvantages: the glide path would take you to the wrong end, the CDI is reversed, and there are no markers. An HSI gives correct sense if you set the front course QDM. The ILS reference datum is a point about 50 feet above the intersection of centre line and threshold that the glide path passes through. PAPIs show the same angle but are set for the mean eye height, so the visual and ILS indications differ slightly depending on the aircraft.
03
In the cockpit Dots and degrees, categories, and what spoils the beams.
e-books by eatpl.in · © 2026 · Do not copy or distribute
ILS presentation
Dots and degrees Shown on a CDI or an HSI Localiser: 0.5° a dot , full scale 2.5° Glide path: 0.14° a dot , full scale 0.7° Max safe below the glide path: half scale , 2.5 dots fly up (0.35°) HSI: set the course selector to the runway QDM LOC 0.5°/dot full scale 2.5° GP 0.14°/dot full scale 0.7° max safe: 2.5 dots fly up
Chapter 9 · Instrument Landing System
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
Localiser and glide path deviation appear on a CDI or an HSI. The localiser needle is 0.5 degrees a dot, full scale 2.5 degrees. The glide path needle is much more sensitive: 0.14 degrees a dot, full scale 0.7. The maximum safe deviation below the glide path is half scale, 2.5 dots fly up. On the HSI set the course selector to the runway QDM and the indications are always in the correct sense.
Reading the needles
Fly towards the needles fly RIGHT and UP fly LEFT and UP fly RIGHT and DOWN on LOC and GPExam: 150 Hz stronger on both = right of c/l and below the glide path: fly LEFT and UP . 90 Hz on both: left and above: fly RIGHT and DOWN .
Chapter 9 · Instrument Landing System
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
The needles show where the localiser and glide path are: fly towards them. Needle right and up: the centre line is to your right and the glide path above you, so fly right and up. Remember the tones: 150 hertz dominant in both receivers means you're right of the centre line and below the glide path, so fly left and up.
ILS categories
How low you can go Cat DH RVR I ≥ 200 ft (60 m) ≥ 550 m II 100–200 ft ≥ 300 m IIIA < 100 ft or none ≥ 200 m IIIB < 50 ft or none 75–200 m IIIC none none
Facility : Cat I guidance to 200 ft or less; Cat II to 50 ft ; Cat III to and along the runway .
Cat I · DH 200 ft · RVR 550 m Cat II · DH 100 ft · RVR 300 m IIIA < 100 ft · IIIB < 50 ft heights exaggerated
Chapter 9 · Instrument Landing System
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
Two sets of categories. The facility categories: a Cat I ILS gives guidance down to where the localiser meets the glide path at 200 feet or less above the threshold; Cat II, 50 feet or less; Cat III, with ancillary equipment, to and along the runway surface. The operational categories for an aircraft and crew: Cat 1, DH at least 200 feet and RVR at least 550 metres; Cat 2, DH 100 to 200 feet and RVR 300; Cat 3A, DH below 100 feet or none, RVR 200; 3B, DH below 50 feet or none, RVR 75 to 200; 3C, no limits. Cat 2 and 3 need a suitable aeroplane, qualified crew, an equipped aerodrome, and a demonstrated safety level.
Errors and accuracy
Bends, scallops, noise; keep the area clear Beam bends (atmosphere), scalloping (reflections: fast needle wobble), beam noise Critical area : vehicles and aircraft excluded during all ILS operationsSensitive area : movement controlled during low visibility operationsCat II/III holds further back, signed, maybe red stop barsSnow and heavy rain attenuate; FM broadcasts just below 108 MHz can spill over Pilot checks: no flags , and monitor the ident : if it stops, discontinue critical / sensitive GP critical area Cat II/III hold normal hold scalloping: reflections make the beam wiggle
Chapter 9 · Instrument Landing System
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
ILS indications can suffer beam bends from atmospheric conditions, scalloping from reflections, which makes the needles fluctuate too fast to follow, and beam noise. Large objects, including moving vehicles and aircraft, cause multipath. So there's a critical area round each aerial, from which vehicles and aircraft are excluded during all ILS operations, and a larger sensitive area controlled during low visibility operations; Cat II/III holding points are further from the runway. Snow and heavy rain attenuate the signal, and FM broadcast stations just below 108 megahertz can spill into the band. Check the flags are clear and monitor the ident; if it stops, discontinue.
04
The numbers Heights and rates of descent by the 1 in 60 rule; the approach chart.
e-books by eatpl.in · © 2026 · Do not copy or distribute
ILS calculations
1 in 60: height and rate of descent Height (ft) ≈ angle × range (nm) × 100 ROD (fpm) ≈ 5 × groundspeed (3° only)
4 nm, 3°, 150 kt: 1200 ft (trig 1274) and 750 fpm (trig 796) 1 in 60 slightly under-estimates : a gross-error check Other angles: work it for 3°, then ÷ 3 × angle 1 nm 300 ft 2 nm 600 ft 3 nm 900 ft 4 nm 1200 ft 3° ≈ 300 ft per nm
Chapter 9 · Instrument Landing System
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
Use the 1 in 60 rule to check height and predict rate of descent. Height is angle times range in miles times 6076 over 60, which simplifies to angle times range times 100: 3 degrees at 4 miles is 1200 feet; trigonometry gives 1274, so the rule under-estimates slightly, which is fine for spotting gross errors. Rate of descent is height loss per mile times miles per minute: for 3 degrees, 300 times groundspeed over 60, which is 5 times groundspeed: 150 knots needs 750 feet a minute, trig 796. For other angles, work it for 3 degrees, divide by 3 and multiply by the angle.
The ILS approach chart
Segments, safe altitudes and minima
Initial approach Up to the IAF (initial approach fix).
Intermediate Between the IAF and the FAF (final approach fix).
Final approach From the FAF to landing or missed approach.
Sector safe altitudes Minimum altitudes by the sector you arrive from: often a circle in the corner of the chart.
Landing minima DH and RVR : ATC will usually ask you to check them before the approach.
Chapter 9 · Instrument Landing System
24
e-books by eatpl.in · © 2026 · Do not copy or distribute
An ILS approach chart divides the procedure into three segments: initial approach up to the initial approach fix; intermediate, from the IAF to the final approach fix; and final approach after the FAF. Sector safe altitudes depend on which sector you arrive from, shown in a circle on many charts. The landing minima are the decision height and the RVR, which ATC will normally ask you to check before the approach.
Summary
What to take into the exam Frequencies LOC 108–111.975 (odd), 40 ch. GP 329.15–335 UHF, paired. Markers 75 MHz.
Markers OM blue 400 Hz dashes; MM amber 1300 Hz dot-dash, 1050 m; IM white 3000 Hz dots.
Coverage LOC 25 nm ±10°, 17 nm ±35°. GP 10 nm ±8°, 0.45φ–1.75φ.
Principle LOC 90 left / 150 right; GP 90 above / 150 below. DDM 0 on the beam. False GP ≈ 2φ, above.
Indications LOC 0.5°/dot (2.5°); GP 0.14°/dot (0.7°); max safe 2.5 dots fly up. Back course reversed on CDI.
Categories I 200 ft/550 m; II 100/300; IIIA <100/200; IIIB <50/75; IIIC none.
Chapter 9 · Instrument Landing System
25
e-books by eatpl.in · © 2026 · Do not copy or distribute
Six points to know cold: the frequencies, the markers, the coverage figures, the lobes and modulations, the needle sensitivities, and the categories.
Practice · Questions 1
Try these 1. Localiser coverage extends ___ either side of the on-course line out to ___ nm: (a) 10°, 35 (b) 35°, 10 (c) 35°, 17 (d) 25°, 25
2. Upper and lower limits of a 3.5° glide path: (a) 6.125° – 1.575° (b) 7.7° – 1.225° (c) 5.25° – 1.35° (d) 3.85° – 3.15°
3. The minimum angle of a false glide path on a 3° glide path: (a) 6° (b) 5.35° (c) 1.75 × GP (d) 0.7 × GP
4. Over the middle marker: (a) low dashes, blue (b) high dots, amber (c) alternating medium dots and dashes, amber (d) one Morse letter, white
5. Stronger 150 Hz than 90 Hz on the approach. To get on c/l and GP fly: (a) down and left (b) up and left (c) up and right (d) down and right
6. Upper and lower limits of a 3° glide path: (a) 0.35°, 0.70° (b) 3°, at least 6° (c) 5.25°, 1.35° (d) 10°, 35°
7. A UK Cat 2 ILS: (a) guidance to 50 ft above the threshold (b) a 7.5° glide path (c) guidance along the runway (d) a false GP exactly 2×
Chapter 9 · Instrument Landing System
26
e-books by eatpl.in · © 2026 · Do not copy or distribute
Seven questions; answers after the next slide. All can be set up in the ILS Lab.
Practice · Questions 2
Try these 9. Intercepting the localiser outside the published coverage angle, you: (a) may get false on-course or reverse sense (b) normally get nothing (c) get uncoded signals (d) get correct indications
10. Outer marker visual: (a) dots and dashes, blue (b) dots 3/s, blue (c) dashes 2/s, amber (d) dashes 2/s, blue
11. Max safe fly-up on a 5-dot indicator: (a) half scale above c/l (b) 2.5 dots fly up (c) just before full scale (d) 1.3 dots fly up
13. Glide path azimuth coverage: (a) ±8° to 10 nm (b) ±10° to 8 nm (c) ±12° to 17 nm (d) ±35° to 25 nm
14. QDM 264; both receivers mainly 90 Hz. You are: (a) north, below (b) south, above (c) north, above (d) south, below
8. Left of the centre line and at maximum safe deviation below the glide path: what does the indicator show?
Chapter 9 · Instrument Landing System
27
e-books by eatpl.in · © 2026 · Do not copy or distribute
Seven more. For question 14, picture yourself flying 264, roughly west: your left is south.
Practice · Answers
Answers and working Q Ans Why 1 c 35°, 17 nm 2 a 0.45 × 3.5 = 1.575; 1.75 × 3.5 = 6.125 3 a About 2 × 3° 4 c Amber, dot-dash, 1300 Hz 5 b 150 = right and below 6 c 1.35° to 5.25° 7 a Cat II: 50 ft
Q Ans Why 8 d LOC needle right, GP 2.5 dots fly up 9 a False course, reverse sense 10 d Blue dashes 2/s 11 b Half scale, 2.5 dots 13 a ±8° to 10 nm 14 b 90 = left (south) and above
Chapter 9 · Instrument Landing System
28
e-books by eatpl.in · © 2026 · Do not copy or distribute
Question 14: flying 264, the 90 hertz localiser lobe is on your left, which is south; 90 hertz on the glide path is the upper lobe, so above. Question 12, not shown, is d: outside coverage the localiser can give false course and reverse sense, the glide path intermittent and incorrect indications.
Fly an ILS in plan and profile; drag the aircraft anywhere Live LOC and GP needles, 90/150 Hz, DDM Marker lights and tones as you cross the fans False glide path, coverage and back course 1-in-60 calculator, categories, all 14 questions Open the ILS Lab →
fly towards the needles
Chapter 9 · Instrument Landing System
29
e-books by eatpl.in · © 2026 · Do not copy or distribute
The ILS Lab: fly the approach, watch the needles and markers, and check the numbers.
eatpl.in · Radio Navigation · Chapter 9
ILS Lab
Fly an ILS approach in 3D, plan and profile; read the needles, watch the marker lights, and check the numbers.
Fly the ILS Numbers Practice
Coverage and false glide path
All the chapter's questions. Set each up, read the answer in the lab, then open the working.
E-book and lab by eatpl.in · © 2026 eatpl.in. For the personal study of eatpl.in students. Do not copy or distribute.
3D view Orbit Chase Pilot
Drag to turn the view. Heights ×4. Blue: localiser plane · amber: glide path plane · green: the approach.