ionosphere skywave surface waveRadio Navigation · Chapter 2
Radio Propagation Theory How radio waves travel: what weakens them, the surface wave, the space wave and the skywave, and why each band suits the job it does.
© 2026 eatpl.in. All rights reserved. For the personal study of eatpl.in students only. No part may be copied, reproduced, shared or distributed in any form without prior written permission. Unauthorised use may attract civil and criminal liability under the Copyright Act, 1957.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Propagation simply means how radio waves travel through the atmosphere. The path a frequency takes decides what it can be used for and what limits it. This chapter covers attenuation, the four propagation paths that matter in aviation, the ionosphere and skywave, HF communications and SELCAL, and super- and sub-refraction.
Chapter roadmap
What this chapter covers 01
What weakens a signal Attenuation, the inverse square law, static, power, receiver sensitivity and directivity.
02
Paths near the Earth Surface wave, space wave and line of sight, and super- and sub-refraction.
03
The ionosphere Layers, skywave, critical angle, skip distance, dead space, HF communications and SELCAL.
Chapter 2 · Radio Propagation Theory
02
e-books by eatpl.in · © 2026 · Do not copy or distribute
Three parts: the factors that weaken a signal, the non-ionospheric paths, then the ionosphere and skywave.
01
What weakens a signal Attenuation is the loss of signal strength as a wave travels away from the transmitter.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Attenuation
Absorption plus the inverse square law Absorption : energy taken by air, water vapour, dust, rain, vegetation, the surface and the ionosphereAbsorption (except ionospheric) increases with frequency ; very significant above about 1000 MHz Inverse square law : power falls with the square of rangeTo double the range you need 4 × the power.
Tx 4 W 1 m² at R 1 W 1 W 1 W 1 W 4 m² at 2R Double the range → a quarter of the power
Chapter 2 · Radio Propagation Theory
04
e-books by eatpl.in · © 2026 · Do not copy or distribute
Attenuation is the loss of signal strength as a wave travels out from the transmitter, and it has two parts. Absorption: energy is absorbed and scattered by air molecules, water vapour, dust, water droplets, vegetation, the Earth's surface and the ionosphere. Apart from ionospheric absorption, it gets worse as frequency rises and is very significant above about 1000 megahertz. Second, the inverse square law: the energy spreads over the surface of a growing sphere, so at twice the range it covers four times the area. 4 watts per square metre becomes 1. So doubling range needs four times the power. Exam: 50 to 100 nautical miles needs power times 4.
Factors affecting propagation
Static, power, sensitivity and directivity
Static interference From weather, people and geology. Worse at low frequencies , negligible at VHF and above, but anything passing through the ionosphere collects it. Measured as signal-to-noise ratio (S/N).
Power More power gives more range, within the inverse square law: 2 × range needs 4 × power.
Receiver sensitivity Less internal noise lets a receiver use weaker signals, so more range, but it is expensive.
Directivity Concentrating power into a beam gives more range for the same power, but only in that direction.
Chapter 2 · Radio Propagation Theory
05
e-books by eatpl.in · © 2026 · Do not copy or distribute
Four more factors. Static: atmospheric and man-made electrical noise, worst at low frequencies and generally negligible at VHF and above, although anything travelling through the ionosphere collects interference at all frequencies. The ratio of wanted signal to noise is the signal-to-noise ratio. Power: more power, more range, but only as the square root. Receiver sensitivity: a quieter receiver can use weaker signals, but it costs. Directivity: a beam gives more range or needs less power, but only in the beam's direction.
Propagation paths
Four paths matter in aviation Path Type Frequencies Used for Surface wave Non-ionospheric 20 kHz – 50 MHz Used 20 kHz – 2 MHz (LF, lower MF) Space wave Non-ionospheric Above 50 MHz VHF and above, line of sight Skywave Ionospheric 20 kHz – 50 MHz Used 2 – 30 MHz (HF) Satellite Ionospheric UHF, SHF GNSS and satcom (Chapter 19) Ducting — Below 20 kHz (VLF) Not examined: no civil VLF systems
Chapter 2 · Radio Propagation Theory
06
e-books by eatpl.in · © 2026 · Do not copy or distribute
Five propagation paths exist; four matter in aviation. Non-ionospheric: the surface wave, roughly 20 kilohertz to 50 megahertz but used from 20 kilohertz to 2 megahertz, and the space wave above 50 megahertz. Ionospheric: the skywave, present from 20 kilohertz to 50 megahertz but used from 2 to 30 megahertz, and satellite propagation at UHF and SHF, covered with GNSS. VLF ducting below 20 kilohertz exists but there are no civil systems there, so it is not examined.
02
Paths near the Earth Low frequencies follow the curve of the Earth; VHF and above travel line of sight.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Part two: non-ionospheric propagation.
Surface wave
Bent round the Earth by diffraction About 20 kHz to 50 MHz; the main path for LF and lower MF (30 kHz – 2 MHz) Range falls as frequency rises ; effectively none above HF Further over sea than land (sea conducts well)Vertical polarisation : horizontal is attenuated very quicklyAt 300 kHz: sea ≈ 3 × √P, land ≈ 2 × √P (P in watts). 10 kW → about 300 nm over sea, 200 nm over land.
wave front bends round the Earth (diffraction) slowed at the surface
Chapter 2 · Radio Propagation Theory
08
e-books by eatpl.in · © 2026 · Do not copy or distribute
The surface wave exists from about 20 kilohertz to 50 megahertz. The part of the wave touching the Earth is slowed, so the wave bends round the curve of the Earth: diffraction. Its range depends on frequency, surface and polarisation. Higher frequency, more surface attenuation, shorter range; above HF it is effectively gone. Sea conducts better than land, so ranges are greater over sea. Horizontal polarisation is attenuated very fast, so vertical polarisation is used. For 300 kilohertz, range over sea is about 3 times root power and over land 2 times root power: 10 kilowatts gives about 300 nautical miles over sea and 200 over land. Because the wave slows more over land, it bends as it crosses a coast: coastal refraction, covered in ADF.
Space wave
Line of sight at VHF and above A direct wave plus a ground-reflected wave At VHF and above waves behave like light: there is a radio horizon A little atmospheric refraction takes it slightly beyond the visual horizon Below the line-of-sight range, no amount of power will help Range (nm) = 1.23 × (√HTX + √HRX ) · heights in feet
Receiver 1600 ft, transmitter 1024 ft: 1.23 × (40 + 32) = 88.6 nm
direct wave ground-reflected wave Tx
Chapter 2 · Radio Propagation Theory
09
e-books by eatpl.in · © 2026 · Do not copy or distribute
The space wave is a direct wave plus a ground-reflected wave. At VHF and above radio waves behave much like light, so there is a radio horizon and propagation is line of sight. A little atmospheric refraction bends the waves slightly towards the Earth and extends the range a little beyond the geometric horizon. This chapter uses 1.23 times the sum of the square roots of the heights in feet. The question bank has used 1.25, which is the figure in the VOR chapter, so check the options. Receiver at 1600 feet, transmitter at 1024 feet: root 1600 is 40, root 1024 is 32, 72 times 1.23 is 88.6 nautical miles. Below line of sight, power makes no difference.
Super- and sub-refraction
Weather changes line-of-sight range above 30 MHz
Super-refraction: up to +40% Humidity decreasing with height · temperature falling more slowly than standard · fine weather, high pressure · warm air over a cooler surface. Extreme case: warm dry air over cool moist air forms a duct , giving very long ranges (common near deserts by the sea, e.g. Mediterranean, Caribbean).
Sub-refraction: up to −20% Much rarer. Humidity increasing with height · temperature falling faster than standard · poor weather, low pressure · cold air over a warm surface.
Chapter 2 · Radio Propagation Theory
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
Above 30 megahertz the weather changes the refraction. Super-refraction bends the waves down more than normal, increasing line-of-sight range by as much as 40 percent. Conditions: humidity decreasing with height, temperature falling more slowly than standard, fine weather and high pressure, warm air over a cooler surface. In extreme cases, warm dry air above cool moist air, a duct forms and ranges become exceptionally long; it is common where desert borders sea, the Mediterranean and Caribbean, and in winter anticyclones. Sub-refraction is rarer and cuts range by up to 20 percent: humidity increasing with height, temperature falling faster than standard, poor weather and low pressure, cold air over a warm surface.
03
The ionosphere Layers of charged particles that can bend radio waves back to Earth.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Part three: ionospheric propagation.
The ionosphere
Made by the Sun, changing all the time From about 60 km up; very low pressure Solar UV knocks electrons off atoms → free electrons and positive ions Electrons keep recombining, so ionisation peaks about 1400 local time and is lowest just before sunrise Higher in summer and at low latitudes Solar flares cause sudden very high ionisation and disruption Ionisation increases with height, but not linearly : it forms layers Each layer is densest at its centre Stable by day and by night; dawn and dusk are turbulent, with interference and disruption Exam: ionisation is highest at low latitudes, and the E layer is higher at night.
Chapter 2 · Radio Propagation Theory
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
The ionosphere runs from about 60 kilometres up. Ultraviolet and shorter-wavelength solar radiation knocks electrons off atoms, leaving free electrons and positive ions. Electrons constantly try to recombine, so ionisation peaks shortly after midday, around 1400 local, and is lowest just before sunrise, not at midnight. It is higher in summer and at low latitudes, and solar flares can push it to extreme levels, enough to shut down satellites. Ionisation increases with height but not linearly, because gravity and the Earth's magnetic field sort the gases into layers, densest at their centres. Conditions are stable by day and by night, but dawn and dusk are electrically turbulent and disrupt systems that use the ionosphere.
The layers
D by day only, E always, F splits by day D about 75 km: forms at sunrise, gone at sunsetE about 125 km: present 24 hours; lower by day, higher at nightF about 225 km: splits into F1 and F2 by day, rejoins at nightF2 rises in summer, above 400 km DAY D 75 km E 125 km F1 F2 225 km + NIGHT E higher F F1 + F2 merge Ionisation peaks about 1400 local, lowest just before dawn
Chapter 2 · Radio Propagation Theory
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
Three layers. The D region at about 75 kilometres forms at sunrise and disappears at sunset. The E layer at about 125 kilometres is there 24 hours a day; it comes down at sunrise and rises after sunset. The F layer at about 225 kilometres splits into F1 and F2 at sunrise and rejoins at sunset; F2 depends on season and can climb above 400 kilometres in summer.
Skywave
Critical angle, skip distance and dead space A wave entering a layer at an angle is refracted; if it bends to the horizontal before the centre, it returns to Earth Critical angle : the angle from the vertical of the first returning skywaveSkip distance : transmitter to where that first skywave landsDead space : from the end of the surface wave to the first skywave: no signalUp to about 2 MHz refraction is at the E layer; 2–50 MHz at the F layers. Above 50 MHz, normally no skywave.
ionised layer escapes critical angle surface wave dead space skip distance
Chapter 2 · Radio Propagation Theory
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
A wave crossing a layer at right angles is slowed but goes straight on. One entering at an angle is refracted away from the normal; if it has turned to the horizontal before reaching the layer's centre it keeps bending and comes back down: skywave. Start at the vertical with a frequency that goes straight through, and tilt the beam: at some angle the wave first returns. That is the critical angle, measured from the vertical. The distance to where that first returning skywave lands is the skip distance. Between the end of the surface wave and that point there is nothing: the dead space. Generally up to 2 megahertz is refracted at the E layer and 2 to 50 at the F layers; above 50 megahertz only abnormal solar activity gives skywave, so VHF navigation aids do not.
What changes the skip distance
Ionisation, frequency and layer height Change Critical angle Skip distance Dead space Ionisation increases (day, summer, low latitude) Smaller Shorter Smaller Ionisation decreases (night) Larger Longer Larger Frequency increases Larger Longer Larger (surface wave also shorter) Frequency decreases Smaller Shorter Smaller Refracting layer higher (F instead of E) — Longer —
Chapter 2 · Radio Propagation Theory
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
More ionisation means more refraction, so a smaller critical angle and shorter skip and dead space; less ionisation the reverse. Higher frequency means less refraction, so a larger critical angle and longer skip distance, and the dead space grows twice over because the surface wave also gets shorter. Lower frequency the reverse. And a higher refracting layer gives a longer skip, so F-layer skywave reaches further than E-layer.
LF and MF skywave
Absorbed by day, interfering by night By day the D layer absorbs energy below about 2 MHz: no LF/MF skywave At night the D layer is gone: skywave returns from the E layer So LF/MF skywave is unreliable for long-range use Night skywave at short range interferes with surface-wave systems such as ADF (Chapter 7) DAY E D absorbs ✕ surface wave NIGHT E skywave surface wave
Chapter 2 · Radio Propagation Theory
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
By day the D region absorbs radio energy below about 2 megahertz, so there is no LF or MF skywave. At night the D region is effectively gone and skywave refracted at the E layer appears. That makes LF and MF skywave useless for continuous long-range work, and worse, night skywave at fairly short range interferes with systems that rely on the surface wave, notably ADF. That is night effect, in Chapter 7.
Achievable ranges
One hop, many hops, and VLF ducting
E layer, one hop Average maximum about 1350 nm (layer at 125 km).
F layer, one hop Average maximum about 2200 nm (layer at 225 km).
Multi-hop Ground reflects the wave back up: ranges up to half the Earth's circumference .
VLF ducting Below about 20 kHz the Earth and ionosphere form a wave guide round the planet. Not examined.
Chapter 2 · Radio Propagation Theory
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
Maximum single-hop range is when the ray leaves and arrives tangential to the Earth. From the E layer at 125 kilometres that is on average about 1350 nautical miles; from the F layer at 225 kilometres about 2200. With multi-hop, the wave reflects off the Earth back up to the ionosphere again, reaching half way round the world. At VLF the wavelength is similar to the height of the lower ionosphere, and the Earth and ionosphere form a duct; no civil equipment uses it.
HF communications
Choosing a frequency Over oceans, until satcom, long range means HF skywave MUF : maximum usable frequency for a range = the first returning skywaveOWF = 0.85 × MUF, a margin against falling ionisationNight needs roughly half the day frequency Short range → lower frequency; long range → higher DAY (UK side) NIGHT (USA side) aircraft at sunrise 12 MHz about 6 MHz UK USA
Chapter 2 · Radio Propagation Theory
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
Over the oceans, until satellite communications take over, the practical long-range option is HF skywave. Surface wave would need very low frequencies, heavy equipment, lots of static and low data rates. The maximum usable frequency for a range is the one whose first returning skywave lands there: shortest path through the ionosphere, least attenuation and static. But ionisation fluctuates and a dip would put you in the skip, so the optimum working frequency is used, 0.85 of the MUF. Night needs roughly half the day frequency, and longer ranges need higher frequencies. The classic question: mid-Atlantic at sunrise, talking to the UK on 12 megahertz. The refraction point towards the UK is in daylight; towards the USA it is still night, so expect about 6 megahertz.
SELCAL
So pilots don't have to listen to HF static
The problem HF picks up heavy static through the ionosphere and may bring in several stations at once; a continuous listening watch is tiring.
The answer Selective calling: each HF radio has a unique 4-letter code (e.g. ABCD). ATC sends the code and a chime alerts the crew.
In use Give ATC your SELCAL code, check it works on first contact, then rely on it. To talk to ATC, just call. Also on VHF in some remote areas.
Chapter 2 · Radio Propagation Theory
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
HF signals have travelled through the ionosphere, so they carry heavy static, and at long range more than one ground station may be heard. A continuous listening watch is stressful. SELCAL, selective calling, gives each HF radio a unique four-letter code. The crew tells ATC the code, checks it on first contact, then relies on ATC to call them with it. If the pilot wants ATC, he simply calls. SELCAL is also used on VHF in some remote areas.
Summary
Bands and their propagation paths Band Path used Also present VLF Ducting LF Surface wave Skywave MF Surface wave Skywave HF Skywave Surface wave VHF and above Space wave
Double range → 4 × power Range = 1.23 × (√HTX + √HRX ) Surface wave at 300 kHz: sea 3√P, land 2√P More ionisation → shorter skip; higher frequency → longer skip E layer 125 km, 1350 nm; F layer 225 km, 2200 nm OWF = 0.85 MUF; night ≈ half day frequency
Chapter 2 · Radio Propagation Theory
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
The summary table: VLF ducting; LF and MF surface wave with skywave present; HF skywave with some surface wave; VHF and above, space wave. And the numbers to carry: four times power for double range, the line-of-sight formula, the surface wave rule at 300 kilohertz, the skip rules, layer heights and ranges, and OWF.
Practice · Questions
Try these 1. Greatest surface wave range? (a) 243 MHz (b) 500 kHz (c) 2182 kHz (d) 15 MHz
2. To increase a VHF transmitter's range from 50 to 100 nm, multiply the power by: (a) 2 (b) 8 (c) 16 (d) 4
3. A 300 kHz transmitter of 1600 W: effective range over the sea? (a) 52 nm (b) 80 nm (c) 35 nm (d) 120 nm
4. Maximum range for an aircraft at 2500 ft to a VHF station at 196 ft: (a) 80 nm (b) 64 nm (c) 52 nm (d) 65 nm
5. Minimum height to be detected at 200 nm by a radar at 1600 ft? (a) 25 500 ft (b) 15 000 ft (c) 40 000 ft (d) 57 500 ft
6. Average height of the E layer, and maximum skywave range? (a) 60 km, 1350 nm (b) 125 km, 2200 km (c) 225 km, 2200 km (d) 125 km, 1350 nm
Chapter 2 · Radio Propagation Theory
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
Six end-of-chapter questions. Answers on the next slide; the calculations can be checked in the Propagation Lab.
Practice · Answers
Answers and working Q Answer Working 1 (b) 500 kHz Lowest frequency, least surface attenuation 2 (d) 4 Inverse square law: 2² = 4 3 (d) 120 nm 3 × √1600 = 3 × 40 4 (a) 80 nm 1.23 × (√2500 + √196) = 1.23 × 64 = 78.7 5 (b) 15 000 ft 200 ÷ 1.23 = 162.6; − √1600 (40) = 122.6; 122.6² ≈ 15 000 6 (d) 125 km, 1350 nm E layer average height and single-hop range
Chapter 2 · Radio Propagation Theory
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
Question 4 gives 78.7 with 1.23, or 80 with 1.25: either way the answer is (a). Question 5 runs the formula backwards: divide the range by the constant, take off the root of the known height, and square what is left.
Try it yourself
Propagation Lab Slide the frequency from LF to VHF and watch the paths change Switch day and night, and raise or lower the ionisation See critical angle, skip distance and dead space Line-of-sight, power and surface wave calculators Open the Propagation Lab →
dead space skip distance changes with f
Chapter 2 · Radio Propagation Theory
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
The Propagation Lab draws the surface wave, skywave and dead space for any frequency, by day or night and at any ionisation level, and has calculators for the chapter's formulas.
eatpl.in · Radio Navigation · Chapter 2
Propagation Lab
Change the frequency, time of day, surface and ionisation, and see which propagation paths you get.
Paths Calculators Practice
What you get
A simplified teaching model: the shapes and trends match the course notes; exact ranges vary in real life.
End-of-chapter questions. Set each one up, read the answer in the lab, then open the working.
E-book and lab by eatpl.in · © 2026 eatpl.in. For the personal study of eatpl.in students. Do not copy or distribute.
Side view
Surface wave Skywave Dead space Space wave