Radio Navigation · Chapter 11
Radar Principles Pulses, echoes and a turning beam: how radar measures range and bearing, and what limits how far and how finely it can see.
© 2026 eatpl.in. All rights reserved. For the personal study of eatpl.in students only. No part may be copied, reproduced, shared or distributed in any form without prior written permission. Unauthorised use may attract civil and criminal liability under the Copyright Act, 1957.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Radar stands for radio detection and ranging. This chapter covers the types of pulsed radar, what radar is used for, why it uses high frequencies, the pulse technique, how range is measured, what sets the maximum and minimum range, resolution, moving target indication and radar aerials.
Chapter roadmap
What this chapter covers 01
Radar basics Primary and secondary radar, uses, and why radar works at VHF and above.
02
Pulses and range PRF and PRI, the echo principle, maximum and minimum range.
03
Performance Range factors, bearing, resolution, MTI and aerials.
Chapter 11 · Radar Principles
02
e-books by eatpl.in · © 2026 · Do not copy or distribute
Three parts: radar basics, pulses and range, and performance.
Introduction
Transmit, reflect, detect RA dio D etection A nd R anging: developed before World War IITransmits radio energy and detects some of it reflected back to the transmitter First pulsed ; later continuous wave (CW) radars too, such as the radio altimeter CW radars have no minimum range limitation Civil use: ground radar for control, separation and navigation ; airborne radar for weather and navigation radar target transmitted pulse echo: very weak (double journey) RAdio Detection And Ranging
Chapter 11 · Radar Principles
03
e-books by eatpl.in · © 2026 · Do not copy or distribute
Radar stands for radio detection and ranging, and was developed before the Second World War for military use on the ground and in the air. It transmits electromagnetic radio energy and detects some of it reflected back to the point of transmission. It started with pulses; continuous wave techniques came later for things like the radio altimeter, because CW radars have no minimum range limitation. Today ground radars control, separate and navigate aircraft, and airborne systems warn of weather and help navigation.
01
Radar basics Primary and secondary, uses and frequencies.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Types of pulsed radars
Primary echoes, secondary replies Primary radar one frequency: the echo is reflected energy pulse out weak echo, same frequency Secondary radar interrogator + transponder: the reply is the aircraft's own energy interrogation reply on another frequency transponder
Primary radar Uses pulses reflected from the target: one frequency throughout.
Secondary radar Transmits on one frequency, receives on another : an interrogator and transponder . The transponder can be in the aircraft or on the ground.
Chapter 11 · Radar Principles
05
e-books by eatpl.in · © 2026 · Do not copy or distribute
There are two types of pulsed radar. A primary radar uses pulses of radio energy reflected from a target, so it uses one frequency throughout. A secondary radar transmits pulses on one frequency but receives on a different one: the object transmits its own energy. It's an interrogator and transponder system, and the transponder can be in the aircraft or on the ground.
Radar applications
Where radar is used
Air traffic control Monitor and vector aircraft on airways, in control zones and near airfields; talk-downs (SRA, military PAR); monitor ILS let-downs; storm clouds.
Air/ground navigation SSR : callsign, altitude, speed, track history, emergencies. DME : accurate slant range from a ground transponder. Doppler : self-contained drift and groundspeed.
Airborne weather radar Range and bearing of cloud; heaviest precipitation and turbulence; cloud height; ground mapping.
Chapter 11 · Radar Principles
06
e-books by eatpl.in · © 2026 · Do not copy or distribute
Air traffic control uses radar to monitor aircraft relative to each other on airways, in control zones and near airfields, vectoring them as needed; to give talk-downs, either a surveillance radar approach or a military precision approach radar; to monitor ILS and other instrument approaches; and for weather. Air-ground navigation systems use radar too: secondary surveillance radar gives ATC callsign, altitude, speed, track history, destination and emergencies; DME gives the pilot slant range from a ground transponder; Doppler gives drift and groundspeed with no ground equipment. Airborne weather radar shows the range and bearing of cloud, the heaviest precipitation and turbulence, cloud height, and maps the ground.
Radar frequencies
VHF and above: why short waves Free from external noise, static and ionospheric scatterShort wavelengths give narrow, efficient beams : target discrimination and bearing Short wavelengths allow shorter pulses Reflection depends on object size against wavelength: shorter waves reflect better long wavelength: wide beam short wavelength: narrow beam
Chapter 11 · Radar Principles
07
e-books by eatpl.in · © 2026 · Do not copy or distribute
Radar systems work at VHF and above for four reasons. These frequencies are free from external noise, static and ionospheric scatter. Shorter wavelengths produce narrow, efficient beams for target discrimination and bearing measurement. They can produce shorter pulses. And reflection depends on an object's size relative to the wavelength, so shorter wavelengths reflect more efficiently.
02
Pulses and range Timing the echo, and what PRF and pulse width allow.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Pulse technique
Short bursts at a fixed rate pulse width pulse recurrence interval (PRI = PRP) PRF = 1 / PRI (pulses per second) time →
Pulse width The duration of each burst. Short in time, but it holds many cycles.
PRI (or PRP) Pulse recurrence interval: the time from one pulse to the next.
PRF (or PRR) Pulse recurrence frequency: pulses per second (pps). PRF = 1 / PRI.
Example PRF 250 pps → PRI = 1 000 000 / 250 = 4000 µs .
Chapter 11 · Radar Principles
09
e-books by eatpl.in · © 2026 · Do not copy or distribute
Primary, secondary and Doppler radars use the pulse technique: radio energy sent in very short bursts of a set shape. The duration of a burst is the pulse length or width, and although it's short it contains many cycles. The pulse recurrence interval, or period, is the time between pulses. The pulse recurrence frequency, or rate, is the number of pulses per second. For example, a PRF of 250 pulses per second gives a PRI of one two-hundred-and-fiftieth of a second, 4000 microseconds.
Distance measurement
Range from the echo time Time from transmission to echo , out and back Range = c × t ÷ 2 500 µs: 300 000 000 × 500 ÷ (1 000 000 × 2) = 75 km Or 162 000 × 500 ÷ (1 000 000 × 2) = 40.5 nm A radar mile (1 nm out and back) takes 12.36 µs : 500 ÷ 12.36 = 40.5 nm range = 40.5 nm (75 km) 0 250 µs 500 µs time out and back c = 300 000 000 m/s = 162 000 nm/s
Chapter 11 · Radar Principles
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
Range is found by timing the interval between transmitting a pulse and receiving its echo. Because the pulse goes out and back, range is the speed of light times the time, divided by two. For an echo time of 500 microseconds, that's 75 kilometres or 40.5 nautical miles. A radar mile, one nautical mile out and back, takes about 12.36 microseconds, so 500 divided by 12.36 also gives 40.5 miles.
Theoretical maximum range
The PRF sets the maximum range pulse 1 pulse 2 pulse 3 echo inside the PRI: correct range echo of pulse 1 from beyond max range arrives after pulse 2: shown at a false short range PRI: time to the most distant target and backRequired Working Answer 187 km 374 000 m ÷ 300 000 000 = 1246 µs PRI 802 pps 200 nm 81 000 ÷ 200 405 pps 170 km 150 000 ÷ 170 882 pps AWR at 400 pps 81 000 ÷ 400 203 nm
Max range (nm) = 81 000 ÷ PRF
Max range (km) = 150 000 ÷ PRF
Greater range needs a lower PRF . In practice a little less: the trace needs fly-back (dead) time .
Chapter 11 · Radar Principles
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
Each pulse must reach the most distant target and come back before the next pulse is sent, or there's no way to tell which pulse an echo belongs to. So the maximum range is set by the PRF: the greater the range, the lower the PRF. For 187 kilometres the pulse travels 374 kilometres, taking 1246 microseconds, so the PRF is 802. For 200 miles, 405; for 170 kilometres, 882; and an AWR at 400 pulses per second reaches 203 miles. The practical range is a little less because the trace needs fly-back or dead time to return to the start, and echoes can't be shown then.
Pulse width
Pulse width sets the minimum range object at 150 m 1 µs pulse = 300 m long (radio travels 300 m per µs) echo returns while the transmitter is still sending the tail: masked minimum range = ½ × pulse length = 150 m per µs
Minimum range Half the pulse length: 150 m per µs . Closer echoes arrive while still transmitting.
Restoration time A design factor: how long the receiver takes to recover after transmitting.
Typical widths 0.1 µs short range · 1–2 µs medium · about 5 µs long range.
Example Surface movement radar down to 500 m: 500 ÷ 150 = 3.3 µs maximum.
Chapter 11 · Radar Principles
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
Pulse width decides the minimum range. Radio waves travel 300 metres in a microsecond, so a 1 microsecond pulse is 300 metres long. An object 150 metres away reflects it so that the echo arrives as the tail leaves the transmitter. Anything closer returns an echo while the transmitter is still transmitting, and two objects in line within 150 metres show as one return. So short-range radars use short pulses, like 0.1 microseconds; medium-range radars 1 to 2; long-range about 5. Restoration time, how long the receiver takes to recover after transmission, also matters. A surface movement radar that must see down to 500 metres needs pulses no wider than 3.3 microseconds.
03
Performance How far, which way, how finely.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Primary radars
Echo for range, searchlight for bearing Pulses concentrated into a beam : the echo principle gives range, the searchlight principle gives bearing (or height) One aerial for transmit and receive ; the receiver listens as soon as the pulse leaves Echoes are very weak : a double journey Aerial size and shape set the beam and lobes: larger aerial, narrower beam Shown on a plan position indicator (PPI) , swept in step with the aerial N range = timing · bearing = beam direction
Chapter 11 · Radar Principles
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
A primary radar concentrates its pulses into a beam. It uses the echo principle for range and the searchlight principle for bearing or height. The transmitter and receiver share one aerial, and the receiver is ready to accept echoes as soon as the pulse has left. Echoes are very weak because of the double journey. The shape and size of the aerial set the main and side lobes and the beam width: the larger the aerial, the narrower the beam. The picture is shown on a plan position indicator, whose trace turns in step with the aerial.
The range of primary radar
Power and the target Signal weakens out and back: power needed ∝ range⁴ Double the range → 16× the power Metal reflects better than wood; size and shape matter Aspect : the side of a fuselage reflects better than the nose; manoeuvring changes the echo 1× power R 16× power 2R range power needed P ∝ R⁴
Chapter 11 · Radar Principles
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
The range of a primary radar depends on the strength of the returning pulses. Because the signal attenuates both out and back, the power needed is proportional to the fourth power of range: to double the range you need sixteen times the power. The target matters too: metal reflects better than wood, size and shape make a big difference, and so does aspect. A manoeuvring aircraft presents changing aspects, and the side of a fuselage reflects better than the nose.
Height, refraction and range
Line of sight and the radar horizon radar shadow radar horizon high: detected low: hidden range (nm) = 1.25 × (√H radar + √H target), heights in feet amsl line of sight plus a little for atmospheric refraction
Line of sight High aircraft are seen; low ones hide in the shadow or behind high ground.
Example Radar 400 ft, target 10 000 ft: 1.25 × (20 + 100) = 150 nm .
Super-refraction Inversion, humidity falling with height: waves bend down, over the horizon .
Sub-refraction Waves bend up and away: range is reduced .
Chapter 11 · Radar Principles
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
Radar frequencies travel in straight lines, giving line-of-sight ranges plus a little extra from refraction. The curvature of the earth leaves much of the surface in shadow, so higher aircraft are more likely to be seen, and high ground screens low flyers. A higher radar head sees further. The theoretical range in nautical miles is 1.25 times the sum of the square roots of the radar height and the target height, in feet amsl. Super-refraction, with a temperature inversion and humidity falling with height, bends waves down and gives over-the-horizon ranges; sub-refraction bends them up and reduces range.
Attenuation by raindrops
Wavelength and rain Above 10 cm : negligible 4 to 10 cm : significant only in tropical rainBelow 4 cm : significant in temperate rain So avoid wavelengths under 3 cm for long range Radar Wavelength ASMI (surface movement) 1.75–2 cm AWR and PAR 3 cm Ground surveillance 10, 23 or 50 cm
0.03 0.1 0.3 1 3 10 wavelength λ (cm), logarithmic scale attenuation temperate rain tropical ASMI AWR · PAR surveillance
Chapter 11 · Radar Principles
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
Raindrops absorb and scatter radar energy, depending on drop size and wavelength. Above 10 centimetres the attenuation is negligible. Between 10 and 4 it matters only in tropical rain. Below 4 centimetres it's significant even in temperate rain, so wavelengths under 3 centimetres shouldn't be used for long range. Surface movement radars use 1.75 to 2 centimetres, airborne weather radar and PAR 3 centimetres, and ground surveillance radars 10, 23 or 50 centimetres.
Measurements and resolution
The resolution rectangle Bearing : beam direction from a fixed datum when the echo arrivesHarmonised : aerial rotation, pulse width, PRF, focusing and powerRadial resolution: half the pulse length (1 µs → 150 m )Azimuth resolution: the full beam width (3° at 120 km → 6 km )Better: short pulses and narrow beams (larger aerial); spot size adds too two aircraft: one echo narrow beam: resolved depth = ½ pulse length (1 µs → 150 m) width = beam width (3° at 120 km → 6 km)
Chapter 11 · Radar Principles
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
Bearing comes from the searchlight principle: a narrow beam turns at a constant speed, the PPI is synchronised with it, and the bearing is the beam's direction when the echo arrives. Rotation speed, pulse width, PRF, focusing and power all have to be harmonised. A point target is painted as a resolution rectangle. Radially it's stretched by half the pulse length, 150 metres for a microsecond, so two targets within that show as one. In azimuth it's stretched by the full beam width: 3 degrees at 120 kilometres is 6 kilometres by the 1 in 60 rule. To resolve close targets you want short pulses and narrow beams, though shorter pulses illuminate the target for less time, and a narrower beam needs a bigger aerial.
Moving target indication (MTI)
Erase what doesn't move without MTI: fixed echoes with MTI: moving targets only MTI
MTI Removes permanent echoes from hills and buildings so the weaker aircraft echoes show.
Second-trace returns An echo of the previous pulse from beyond range can look like a moving target.
Jittering the PRF Changing the PRI between pulses makes second-trace echoes jump about, so they're removed.
Chapter 11 · Radar Principles
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
Surveillance radars use moving target indication to erase returns from stationary objects like hills and buildings, which would otherwise mask the weaker aircraft echoes, so only moving targets are shown. MTI can produce false targets from second-trace returns: an echo of the previous pulse from beyond the selected maximum range, arriving during the next pulse period and looking like a moving target. These are removed by changing the PRI between consecutive pulses, which is called jittering the PRF.
Radar antennae
Horns, dishes and slotted arrays microwave horn parabolic reflector slotted planar array main lobe side lobes
Horn Very often the feed for a large parabolic reflector.
Parabolic reflector Main lobe plus side lobes; side lobe suppression stops their echoes interfering.
Slotted planar array Flat plate: narrower beam, much smaller side lobes , less power, better resolution.
Chapter 11 · Radar Principles
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
Popular radar aerials are the microwave horn, the parabolic reflector and the slotted planar array or flat plate antenna, used widely in radar and satellite systems. Horns are often used to feed large parabolic reflectors. Both reflectors and flat plates produce a main lobe and side lobes, and most radars have side lobe suppression so side lobe echoes don't interfere. The slotted planar array gives a narrower beam with much smaller side lobes, reducing the power needed and improving resolution.
Summary
What to take into the exam Types Primary: reflected, one frequency. Secondary: interrogator and transponder, two frequencies. CW: no minimum range.
Range Range = c × t ÷ 2; 12.36 µs per nm. Max range (nm) = 81 000 ÷ PRF.
Minimum range ½ pulse length: 150 m per µs. Short pulses for short range.
Power and height Power ∝ R⁴ (16× for 2× range). LOS: 1.25(√H + √h) nm.
Resolution Radial ½ pulse length; azimuth = beam width. Short pulses, narrow beams.
MTI and aerials MTI removes fixed echoes; jitter the PRF for second trace. Slotted array: narrow beam, small side lobes.
Chapter 11 · Radar Principles
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
Six points to take in: the types of radar, range from echo time and the PRF limit, minimum range from pulse width, power and height, resolution, and MTI with aerials.
Practice · Questions 1–7
Try these 1. The factor which determines the maximum range of a radar is: (a) pulse repetition rate (b) pulse width (c) power (d) beamwidth
2. The main advantage of continuous wave radars is: (a) no maximum range limitation (b) better range resolution (c) no minimum range limitation (d) better bearing resolution
3. If the PRF of a primary radar is 500 pps, the maximum range will be: (a) 324 nm (b) 300 nm (c) 162 nm (d) 600 nm
4. To double the range of a primary radar the power must be increased by a factor of: (a) 2 (b) 4 (c) 8 (d) 16
5. The time from transmission to echo is 1720 µs. The range is: (a) 139 km (b) 258 km (c) 278 km (d) 516 km
6. A radar needs a maximum range of 100 nm. The maximum PRF is: (a) 1620 pps (b) 1234 pps (c) 617 pps (d) 810 pps
7. If the PRI of a radar is 2100 µs, its maximum range is: (a) 170 nm (b) 315 nm (c) 340 nm (d) 630 nm
Chapter 11 · Radar Principles
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
The questions 1 to 7. Answers follow the second set.
Practice · Questions 8–14
Try these 8. To improve the resolution of a radar display requires: (a) a narrow pulse width and a narrow beam width (b) a high frequency and a large reflector (c) a wide beamwidth and a wide pulse width (d) a low frequency and a narrow pulse width
9. An advantage of a phased array (slotted antenna) is: (a) better resolution (b) less power required (c) reduced sidelobes and clutter (d) all of the above
10. An echo arrives 900 µs after transmission. The range is: (a) 73 nm (b) 270 nm (c) 135 nm (d) 146 nm
11. The factor which limits the minimum detection range of a radar is: (a) PRI (b) transmitter power (c) pulse width (d) PRF
12. Doppler techniques to separate aircraft from fixed objects generate second-trace returns. These are removed by: (a) different transmit and receive frequencies (b) jittering the PRF (c) regular changes in pulse width (d) limiting the power output
13. A radar has a maximum range of 12 km. The maximum PRF is: (a) 25 000 pps (b) 6700 pps (c) 12 500 pps (d) 13 400 pps
14. The bearing of a primary radar is measured by: (a) phase comparison (b) searchlight principle (c) lobe comparison (d) DF techniques
Chapter 11 · Radar Principles
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
The questions 8 to 14. Answers next.
Practice · Answers
Answers Q Ans Why 1 a PRF sets max range 2 c CW: no minimum range 3 c 81 000 ÷ 500 = 162 nm 4 d Power ∝ R⁴ 5 b 1720 × 150 m = 258 km 6 d 81 000 ÷ 100 = 810 pps 7 a 2100 ÷ 12.36 = 170 nm
Q Ans Why 8 a Short pulse, narrow beam 9 d All of the above 10 a 900 ÷ 12.36 = 73 nm 11 c Pulse width 12 b Jittering the PRF 13 c 150 000 ÷ 12 = 12 500 pps 14 b Searchlight principle
Chapter 11 · Radar Principles
24
e-books by eatpl.in · © 2026 · Do not copy or distribute
The answers to all fourteen questions, with the one-line reason for each.
Send pulses from a turning 3D radar and time the echoes Change PRF and pulse width: watch max and min range move Make a second-trace echo, then jitter the PRF to kill it MTI, resolution rectangles and beam width Radar horizon and the power-range law Open the Radar Lab →
pulse · echo · range · bearing
Chapter 11 · Radar Principles
25
e-books by eatpl.in · © 2026 · Do not copy or distribute
The Radar Lab: pulses, echoes and limits in 3D.
eatpl.in · Radio Navigation · Chapter 11
Radar Lab
Send pulses, time the echoes and find the limits of range and resolution, in 3D.
Pulses and range Resolution Horizon and power Practice
Pulses and range
Drag the target on the PPI or use the sliders. Pulses travel out along the beam; echoes come back when the beam is on the target.
MTI Jitter PRF
Resolution
Two aircraft close together. Are they one echo or two? Bigger aerials and shorter waves narrow the beam.
Wavelength
3 cm 10 cm
23 cm 50 cm
Radar horizon and power
Line of sight limits low targets; power limits distant ones. Whichever is less wins.
14 practice questions. Set each one up in the lab, read the answer, then open the working.
E-book and lab by eatpl.in · © 2026 eatpl.in. For the personal study of eatpl.in students. Do not copy or distribute.
3D view Orbit Chase Radar
Drag to turn. Orange ripples: pulses out · cyan: echoes back · green: the beam (drawn wider than life). Slow motion.
A-scope: time after each pulse