Radio Navigation · Chapter 14
Secondary Surveillance Radar Ask, and the aircraft answers: interrogations on 1030 MHz, coded replies on 1090 MHz, and the labels on the controller's screen.
© 2026 eatpl.in. All rights reserved. For the personal study of eatpl.in students only. No part may be copied, reproduced, shared or distributed in any form without prior written permission. Unauthorised use may attract civil and criminal liability under the Copyright Act, 1957.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Secondary surveillance radar receives pulses transmitted by the target in reply to interrogations, rather than echoes. This chapter covers its advantages and display, frequencies and modes, the reply code and Mode C, operating procedures and special codes, its disadvantages, and Mode S.
Chapter roadmap
What this chapter covers 01
How SSR works Primary vs secondary, advantages, the display, 1030 and 1090 MHz.
02
Modes and codes P1–P3 spacing, the reply train, the transponder, Mode C, procedures, special codes.
03
Limits and Mode S Garbling, fruiting, too few codes, and how Mode S fixes them.
Chapter 14 · Secondary Surveillance Radar
02
e-books by eatpl.in · © 2026 · Do not copy or distribute
Three parts: how SSR works, modes and codes, and its limits and Mode S.
Introduction
Echo, or answer? Primary : receives the echo of its own pulseSecondary : receives pulses transmitted by the target in reply to an interrogation (SSR, DME)Primary gives better range and bearing, but no identification , and needs high power for the two-way trip Aircraft carries a transponder ; the ground station is the interrogator Pilot sets a four-figure code from ATC; replies are automatic, in pulse code PRIMARY sends a pulse, listens for its own echo faint echo: two-way path, needs high power SECONDARY (SSR) interrogates; the transponder replies with a code 1030 MHz up · strong coded reply on 1090 MHz
Chapter 14 · Secondary Surveillance Radar
03
e-books by eatpl.in · © 2026 · Do not copy or distribute
Primary radar relies on the echo of its own pulse; secondary radar receives pulses transmitted by the target in response to interrogation pulses. SSR is one secondary radar; DME is another. Both primary and secondary radars track aircraft. Primary gives better bearing and range, but can't positively identify individual aircraft, which ATC needs in crowded airspace, and it needs more power for the two-way journey. SSR needs a transponder in the aircraft. The pilot sets a four-figure code allocated by ATC and the transponder replies automatically, in pulse code, when the ground interrogator asks. Each transmission is one way.
01
How SSR works Advantages, display and frequencies.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Advantages of SSR
Less power, no clutter, positive identity Much less power for coverage to 200–250 nm Not dependent on the aircraft's echoing area or aspect Clutter free : no reflected pulsesPositive identity : code and callsign beside the primary returnTrack history, speed, altitude and destination Shows emergency , radio failure or hijack Usually co-located with primary radar to get both SSR aerial · 1030 / 1090 MHz primary reflector (23 cm) turning gear lattice tower equipment room co-located: one rotation gives both pictures
Chapter 14 · Secondary Surveillance Radar
05
e-books by eatpl.in · © 2026 · Do not copy or distribute
Compared with primary radar, SSR needs much less transmitting power for coverage of 200 to 250 miles, doesn't depend on the aircraft's echoing area or aspect, gives clutter-free responses because it doesn't rely on reflections, positively identifies an aircraft by showing its code and callsign beside the primary return, shows track history, speed, altitude and destination, and can show that an aircraft has an emergency, has lost radio or is being hijacked. Used together, you get the advantages of both, so the two aerials are usually co-located, the SSR aerial on top of the primary reflector.
SSR display
One screen, two radars SSR data shown with the primary returns on one screen Callsign or flight numberPressure altitude or flight levelGround speed and destination Track history dots show where it's been Special codes flash a warning label BAW123 120↑ 28 LHR RYR45K 090↓ 25 STN EZY81 240 42 EDI 7700 EMRG 110 31 7000 035 11 label: callsign · FL · GS (tens of kt) · destination squares: SSR + primary · dots: track history
Chapter 14 · Secondary Surveillance Radar
06
e-books by eatpl.in · © 2026 · Do not copy or distribute
SSR information is displayed with the primary radar information on the same screen: callsign or flight number, pressure altitude or flight level, ground speed and destination.
SSR frequencies and transmissions
Ask on 1030 MHz, answer on 1090 MHz 1030 MHz interrogation narrow beam in the horizontal plane 1090 MHz reply omnidirectional interrogator UHF band: 300 MHz 3000 MHz 1030 1090
Ground station Interrogates on 1030 MHz with a narrow beam in the horizontal plane; receives on 1090 MHz .
Aircraft Receives on 1030 MHz ; transponds on 1090 MHz , omnidirectionally .
Band Both in the UHF band: SSR is a secondary pulse radar.
Chapter 14 · Secondary Surveillance Radar
07
e-books by eatpl.in · © 2026 · Do not copy or distribute
The ground station interrogates on 1030 megahertz and receives on 1090. The aircraft receives on 1030 and replies on 1090. The ground aerial transmits a narrow beam in the horizontal plane; the aircraft transmits omnidirectionally, a circular pattern around the aircraft. Both frequencies are in the UHF band.
02
Modes and codes Pulses, transponder, Mode C and special codes.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Modes
P1–P3 spacing tells the transponder what to send MODE A P1–P3 8 µs P1 P2 P3 2 µs 8 µs → identity: reply with the code MODE C P1–P3 21 µs P1 P2 P3 2 µs 21 µs → altitude: reply with the pressure altitude the transponder decodes the mode from the P1–P3 spacing
Mode A Interrogation to identify the aircraft: P1–P3 8 µs .
Mode C Interrogation for an automatic height read-out : P1–P3 21 µs .
Always three pulses P1, P2, P3; P1–P2 fixed at 2 µs .
Chapter 14 · Secondary Surveillance Radar
09
e-books by eatpl.in · © 2026 · Do not copy or distribute
The aircraft is interrogated by a set series of pulses on 1030 megahertz and replies with a coded train on 1090. The two main modes are Mode A, to identify the aircraft, and Mode C, for an automatic height read-out. Three pulses, P1, P2 and P3, are always transmitted. P1 to P2 is fixed at 2 microseconds; P1 to P3 is 8 microseconds for Mode A and 21 for Mode C.
SSR reply pulse pattern
Two framing pulses, twelve code pulses F1 C1 A1 C2 A2 C4 A4 X B1 D1 B2 D2 B4 D4 F2 SPI 20.3 µs 1.45 µs 4.35 µssquawk 4521 squawk 1234 squawk 7700 squawk 2000 A = A4 A2 A1 · B · C · D: each digit 0–7 12 pulses: 2¹² = 4096 codes, 0000–7777 SPI (Ident) shown on the last codeFraming pulses F1 and F2 are 20.3 µs apart . Between them, 12 information pulses (X, for Mode B, unused) each sent or not: 2¹² = 4096 codes, 0000 to 7777 (no 8 or 9). Press Ident and the SPI pulse follows F2 for about 20 s , giving a distinctive display: “squawk ident”.
Chapter 14 · Secondary Surveillance Radar
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
The transponder replies correctly provided the pilot has selected the right mode and the code allocated by ATC. A valid interrogation produces two framing pulses, F1 and F2, 20.3 microseconds apart, with 12 usable information pulses between them; pulse X is for Mode B, currently unused. Each pulse is sent or not, giving 2 to the 12, 4096 codes, numbered 0000 to 7777, so 8 and 9 aren't used. When the pilot presses Ident, usually at ATC's request, the special position identification pulse is added after the last framing pulse, automatically and continuously for about 20 seconds. It produces a distinctive display so the controller can pick out the aircraft.
Transponder controls
Code, mode, ident Four code windows, each 0–7 , set to the code ATC gives OFF · SBY · ON · ALT · TST : ON gives Mode A; ALT adds Mode CREPLY light flashes as it answers interrogationsIDENT : adds the SPI pulse for about 20 sReplies only if the right mode and code are selected ATC TRANSPONDER 4 5 2 1 ALT FL065 R REPLY OFF SBY ON ALT TST code selectors (0–7) IDENT ID flashes when interrogated four-figure code from ATC Ident: SPI pulse for about 20 s OFF · SBY · ON (A) · ALT (A + C) · TST
Chapter 14 · Secondary Surveillance Radar
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
The transponder control unit has the code selectors, a function switch with off, standby, on for Mode A, ALT for Mode A and C, and test, an Ident button, and a reply light that flashes as the aircraft is interrogated.
Mode C
Altitude from the capsule, on 1013.2 Replies with an ICAO code for its height referenced to 1013.2 mb Regardless of the altimeter's pressure setting and the selected code Encoder driven by the aneroid capsule : independent of the subscale Up to 128 000 ft , 100 ft steps, changing at the 50 ft point FL65: 6450 ft shows 065 , 6445 ft shows 064 static pressure aneroid capsule altitude encoder transponder set to 1013.2 hPa inside: the subscale knob is ignored pressure altitude controller sees6470 ft 065 6460 ft 065 6452 ft 065 6450 ft 065 6448 ft 064 6445 ft 064 6440 ft 064 6430 ft 064 6440 ft 064 6448 ft 064 6450 ft 065 6460 ft 065 readout changes at the 50 ft point 100 ft steps · up to 128 000 ft Mode C
Chapter 14 · Secondary Surveillance Radar
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
On a Mode C interrogation the transponder sends an ICAO code for its height referenced to 1013.2 millibars, regardless of the altimeter's pressure setting and the code selected. The encoder is driven mechanically by the altimeter's aneroid capsule, so it's independent of the subscale. It telemeters altitude automatically up to 128 000 feet, changing every 100 feet on the 50 foot points, so the controller sees flight level or altitude. At FL65 the screen shows 065; drifting down from 6450 to 6445 feet changes it to 064.
SSR operating procedure
Keep the code, read it back, verify Mode C Keep an assigned code until told otherwise Change codes or switch off airborne only when instructed Read back the code to be setMode C with Mode A unless told otherwiseReport levels to the nearest 100 ft to verify Mode C Difference over 300 ft (ICAO): switch off Mode C, or 0000 if you can't UK and others: ±200 ft 6000 6100 6200 6300 6400 6500 6600 6700 6800 6900 7000 pilot reports 6500 ft ±300 ft ICAO ±200 ft UK Mode C readout “switch off Mode C” (or squawk 0000 if you can't)
Chapter 14 · Secondary Surveillance Radar
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
Pilots keep a code assigned by an ATS unit unless told otherwise, select, reselect or switch off airborne only when instructed, read back the code to be set, and select Mode C with Mode A unless told otherwise. When reporting levels, they read the current altimeter to the nearest 100 feet, which helps verify the Mode C data. If the readout and the reported level differ by more than 300 feet, the ICAO standard, the pilot is normally told to switch off Mode C, or to select 0000 if Mode C can't be switched off separately. The UK and other countries use plus or minus 200 feet.
Special codes
Four numbers every pilot knows 7700 EMERGENCY EMRG FL110 7600 RADIO FAILURE RCF FL110 7500 UNLAWFUL INTERFERENCE HIJ FL110 2000 NO ATC INSTRUCTIONS 2000 FL035 7000 UK CONSPICUITY 7000 FL035
7700 · 7600 · 7500 Emergency (as soon as practicable, unless already on a discrete code with a service) · radio failure · unlawful interference.
2000 No ATC instructions to operate the transponder, e.g. entering UK airspace from a region where it wasn't required.
7000 (UK) Conspicuity code with Mode C , at and above FL100 (shall) and below (should), unless told otherwise.
Chapter 14 · Secondary Surveillance Radar
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
Some codes are reserved internationally. 7700 indicates an emergency: select it as soon as practicable after declaring one, with due regard to controlling the aircraft, though a discrete code already in use with an air traffic service may be kept. 7600 means radio failure. 7500 means unlawful interference with the flight, unless 7700 is warranted. 2000 is for an aircraft that hasn't been given any transponder instructions, for example entering the UK from an adjacent region where transponders weren't required. In the UK the conspicuity code is 7000 with Mode C: pilots shall select it at and above FL100, and should below, unless given a different code or using a special one. Mode C should be on with all these codes.
03
Limits and Mode S Garbling, fruiting, codes, and selective addressing.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Disadvantages of SSR
Modes A and C at their limits Europe relies ever more on SSR; A/C is at the limit of its capability Garbling : overlapping replies from aircraft on nearly the same bearing within 1.7 nm in rangeFruiting : replies to another interrogator received as interferenceCodes : only 4096 in Mode AAlso: ghosts and shielding interrogator A interrogator B A's display: fruit replies meant for B are heard at A too
Chapter 14 · Secondary Surveillance Radar
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
Air traffic services in Europe rely more and more on SSR, but civil Modes A and C are reaching the limits of their capability. Garbling is overlapping replies from two or more transponders on nearly the same bearing within 1.7 miles of each other along the line from the antenna. Fruiting is interference at one interrogator from a transponder replying to another interrogator. And there are only 4096 Mode A codes.
Garbling
Two replies in the same 20 µs < 1.7 nmfirst aircraft second, 1.1 nm further what the interrogator receives overlap: GARBLE one reply lasts 20.3 µs ≈ 1.7 radar nm (12.36 µs per nm) A reply takes 20.3 µs , just under 1.7 nm in radar miles. Two aircraft on nearly the same bearing and closer than that in range reply into the same window: the pulses interleave and the codes can't be read.
Chapter 14 · Secondary Surveillance Radar
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
The reply pulses are transmitted over 20.3 microseconds, which is just under 1.7 miles in radar miles at 12.36 microseconds per mile. Two aircraft on nearly the same bearing, closer than that along the line from the antenna, reply at almost the same moment, their pulses overlap, and the interrogator can't separate the codes.
Mode S
S for selective addressing Overcomes A/C limits; compatible with them 24-bit address : over 16 700 000 codes, fitted at manufacture for lifeData link : ground-air, air-ground and air-air, over the horizon via a ground networkLess voice : most RTF via the data link and CDUHeight in 25 ft increments; more performance data 4CA2F1calling 4CA2F1… 40621Dcalling 40621D… 3C6589calling 3C6589… A12B7Ecalling A12B7E… 24-bit address: 2²⁴ ≈ 16.7 million codes, one per airframe
Chapter 14 · Secondary Surveillance Radar
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
Mode S is being introduced to overcome the limits of Modes A and C. S stands for selective addressing, and it's compatible with A and C so it can supplement them. The aircraft address is a 24-bit code, over 16.7 million codes, built into the aircraft at manufacture for its whole life. It supports a data link, through a ground network, for uplink and downlink messages over the horizon, and ground-to-air, air-to-ground and air-to-air data exchange. Most RTF messages are intended to move to the data link via the aircraft's CDU, reducing voice. Height is reported in 25 foot increments, with more data on present and intended performance.
Mode S interrogation modes
All Call, Broadcast, Selective, Intermode ALL CALL Mode S aircraft reply with their address BROADCAST message to all Mode S aircraft: no reply SELECTIVE only the addressed aircraft replies INTERMODE A/C/S All Call: every transponder replies A/C
All Call Elicits replies to acquire Mode S transponders.
Broadcast Information to all Mode S transponders: no replies .
Selective Surveillance of and communication with one addressed transponder: only it replies.
Intermode Mode A/C/S All Call : surveillance of A/C, acquisition of S.
Chapter 14 · Secondary Surveillance Radar
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
Mode S interrogates in several ways. All Call elicits replies to acquire Mode S transponders. Broadcast sends information to all Mode S transponders and elicits no reply. Selective is for surveillance of, and communication with, individual transponders: each interrogation gets a reply only from the uniquely addressed transponder. Intermode, the Mode A/C/S All Call, gets replies from A/C transponders for surveillance and acquires Mode S ones.
Benefits of Mode S
Why it's worth it Unambiguous identification Unique address from almost 17 million, plus automatic flight identity; selective calling and data link.
Surveillance integrity Eliminates synchronous garble , resolves over-interrogation , simplifies identity with reflections .
Better air picture Better tracking and situation awareness from identity, tracking and downlinked data.
No code shortage The EUR region's SSR code shortage disappears with unique addresses.
Less R/T No code verification needed; more by data link.
Better STCA Stable speed vector, 25 ft altitude, downlinked vertical rate: earlier, more accurate warning. (Display stays in 100 ft.)
Chapter 14 · Secondary Surveillance Radar
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
Mode S gives unambiguous identification, from a unique address and automatic flight identity reporting, which also allows selective calling and data link. It improves the integrity of surveillance data by eliminating synchronous garble, resolving over-interrogation and simplifying identification with reflections. Controllers get a better air picture. The code shortage in Europe disappears. R/T workload falls: for example, code verification isn't needed. Short term conflict alert improves through no garble, a stabler speed vector, 25 foot altitude where the avionics support it, and downlinked vertical rate, though controllers will still see altitude in 100 foot steps.
Reference: levels of Mode S and DAPS
What each transponder can do Level Capability 1 Mode A/C and S surveillance; address; no data link ; not for international flights 2 Adds standard length data link both ways and aircraft identification: minimum for international flights 3 Adds extended data link ground → air 4 Adds extended data link air → ground
Downlink aircraft parameters Basic Flight identity · capability report · 25 ft altitude · airborne/on ground Enhanced Magnetic heading · IAS/TAS/Mach · roll angle · track angle rate · vertical rate · true track and GS Future Selected FL/altitude · heading · course · IAS/Mach
Chapter 14 · Secondary Surveillance Radar
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
Not in the objectives, but useful: ICAO Annex 10 sets four levels of Mode S transponder. Level 1 is basic surveillance with an address and no data link, not for international traffic. Level 2 adds standard length data link both ways and automatic identification, and is the minimum for international flights. Level 3 adds extended data link from ground to air, and Level 4 extended data link from air to ground. Downlinked aircraft parameters: basic are flight identity, capability report, altitude in 25 feet and flight status; enhanced add magnetic heading, speed, roll angle, track angle rate, vertical rate, and true track and ground speed; in future, the aircraft's selected level, heading, course and speed.
Summary
What to take into the exam SSR Interrogator on the ground, transponder in the aircraft. Less power, no clutter, identity. Aerial on top of the primary.
Frequencies Ground: 1030 MHz narrow beam, receives 1090. Aircraft: receives 1030, replies 1090 omni. UHF pulse.
Modes P1–P2 2 µs. P1–P3: Mode A 8 µs, Mode C 21 µs. F1–F2 20.3 µs, 12 pulses, 4096 codes. SPI 20 s.
Mode C 1013.2 reference, capsule-driven, 100 ft (±50). Off if > 300 ft (UK 200).
Codes 7700 emergency · 7600 radio failure · 7500 hijack · 2000 no instructions · 7000 UK.
Limits and Mode S Garble < 1.7 nm, fruit, 4096 codes. Mode S: 24-bit, data link, 25 ft; All Call, Broadcast, Selective, Intermode.
Chapter 14 · Secondary Surveillance Radar
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
Six summaries: the system, frequencies, modes, Mode C, special codes, and limits and Mode S.
Practice · Questions 1–6
Try these 1. Special codes: emergency ___, radio failure ___, entering UK airspace ___, unlawful interference ___. (a) 7700 7600 2000 7500 (b) 7700 7600 7500 2000 (c) 7600 7500 2000 7700 (d) 7500 7600 2000 7700
2. SSR is a form of ___ radar with type emissions in the ___ band: (a) primary pulse SHF (b) primary pulse UHF (c) secondary FM SHF (d) secondary pulse UHF
3. If the IDENT button is pressed: (a) a momentary distinctive display (b) an ident pulse for 20 s, 4.35 µs before the last framing pulse (c) for 10 s, 4.35 µs after (d) for 20 s, 4.35 µs after the last framing pulse
4. ATC asks you to cancel Mode C if the discrepancy is more than ___ between the radar altitude and your altimeter with the subscale on ___: (a) 100 ft, Regional QNH (b) 300 ft, 1013 hPa (c) 50 ft, 1013 hPa (d) 300 ft, Regional QNH
5. The code for a UK FIR (inbound, crossing) where no other squawk has been allocated: (a) 7500 (b) 7600 (c) 7700 (d) 2000
6. Secondary radars require: (a) a responding target, always an aircraft (b) always ground based (c) an aircraft or a ground based transponder (d) a quiescent target
Chapter 14 · Secondary Surveillance Radar
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
The six questions. Answers next.
Practice · Answers
Answers Q Ans Why 1 a 7700 emergency, 7600 radio failure, 2000 entering the UK, 7500 unlawful interference 2 d Secondary pulse radar, 1030/1090 MHz: UHF 3 d SPI for about 20 s, 4.35 µs after F2 4 b 300 ft; Mode C is referenced to 1013 hPa 5 d 2000: no instructions received 6 c Any transponder: airborne or on the ground (e.g. DME, SSR)
Chapter 14 · Secondary Surveillance Radar
24
e-books by eatpl.in · © 2026 · Do not copy or distribute
Answers to all six, with the reason for each.
Set your squawk, mode and Ident on a working transponder Watch the interrogator paint primary blips and SSR labels Mode C: pressure altitude, the 50 ft change, and the ±300/±200 ft check See the P1–P3 interrogation and the reply train for any code or altitude Make two aircraft garble, add fruit, then fix it with Mode S Open the SSR Lab →
EAT101 065 25 7700 EMRG squawk · ident · Mode C · garble
Chapter 14 · Secondary Surveillance Radar
25
e-books by eatpl.in · © 2026 · Do not copy or distribute
The SSR Lab: transponder, display, pulses and garbling.
eatpl.in · Radio Navigation · Chapter 14
SSR Lab
Squawk, ident and Mode C on a working transponder; watch the interrogator, the pulse trains and two aircraft garbling.
Radar & transponder Pulses Garble & fruit Practice
Your transponder
ATC: “EAT101, squawk 4372.” Set the code, then select ALT.
IDENT
Quick codes
4372 (ATC) 7000 2000 7700 7600 7500
Interrogation and reply
Interrogation
Mode A (8 µs) Mode C (21 µs)
Code
4372 7700 1234 7777 0000 IDENT
Garbling and fruit
Two aircraft on the same bearing from the radar. Close them up in range and watch the replies collide.
System
Mode A/C Mode S selective
Fruit: second interrogator
6 practice questions. Set each one up in the lab, read the answer, then open the working.
E-book and lab by eatpl.in · © 2026 eatpl.in. For the personal study of eatpl.in students. Do not copy or distribute.
3D view Orbit Chase Radar head
Drag to turn.