Radio Navigation · Chapter 6
VHF Direction Finder How a ground station takes a bearing on an aircraft's own radio call, and passes it back as QDM, QDR, QTE or QUJ.
© 2026 eatpl.in. All rights reserved. For the personal study of eatpl.in students only. No part may be copied, reproduced, shared or distributed in any form without prior written permission. Unauthorised use may attract civil and criminal liability under the Copyright Act, 1957.
e-books by eatpl.in · © 2026 · Do not copy or distribute
VHF direction finding is the ground station measuring the direction of the aircraft's own VHF transmission. This chapter covers the equipment, the Q-code bearings, their classification, range and accuracy, and the emergency and let-down services.
Chapter roadmap
What this chapter covers 01
How VDF works The aircraft transmits; an Adcock aerial on the ground measures the bearing.
02
The bearings QDM, QDR, QTE, QUJ; what each is for; classes A to D.
03
Range, accuracy, services Line of sight, error sources, emergency fixing and let-downs.
Chapter 6 · VHF Direction Finder
02
e-books by eatpl.in · © 2026 · Do not copy or distribute
Three parts: how the ground equipment works, the four bearings and their classification, and then range, accuracy and the services VDF provides.
Introduction
The ground station takes the bearing Many aeronautical ground stations take automatic bearings of an aircraft's VHF voice transmissions (118–137 MHz, A3E) Nothing extra in the aircraft: just the VHF radio UHF DF is used only by the militaryStations providing VDF are listed in the AIP and en-route supplements ATC can use VDF to identify an aircraft in a radar environment
Aircraft Transmits on its normal VHF frequency.
Ground Adcock aerial plus display.
Pilot Asks for and is given a bearing by R/T.
Cost Needs ATC: the station must hear you.
Chapter 6 · VHF Direction Finder
03
e-books by eatpl.in · © 2026 · Do not copy or distribute
Most ground stations in the aeronautical mobile service can take automatic bearings of an aircraft's VHF transmissions, 118 to 137 megahertz, emission A3E. There's no special airborne equipment: the aircraft simply transmits. The military also use UHF direction finding. Stations offering VDF are listed in the AIP. ATC can also use a VDF bearing to identify an aircraft in a radar environment.
01
How VDF works A ring of vertical aerials on the ground resolves the direction of the aircraft's call.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Principle of operation
Adcock aerial, cathode ray display Vertically polarised aerial: vertical elements in a circle, the Adcock aerialThe equipment resolves the bearing from the signal at each element Shown as a trace on a cathode ray tube : Cathode Ray DF (CRDF ) Latest high-resolution sets use Doppler principles: digital readout, ±0.5° N E S W CRT trace towards the aircraft QDM 205 CLASS B bearing from station: 025 Adcock aerial (plan)
Chapter 6 · VHF Direction Finder
05
e-books by eatpl.in · © 2026 · Do not copy or distribute
The ground aerial is vertically polarised, an array of vertical elements arranged in a circle: the Adcock aerial. The equipment resolves the bearing from the signal received at each element and displays it as a trace on a cathode ray tube, pointing towards the aircraft; hence Cathode Ray DF. The latest high-resolution equipment uses Doppler principles and gives a digital readout accurate to half a degree. Here the trace points to 025, so the aircraft bears 025 from the station and the QDM, the heading to steer to the station, is 205.
Radiotelephony
Asking for a bearing The pilot calls on the station's VHF frequency, transmitting long enough for the bearing to be taken:
“QDM QDM QDM, Oxford Approach, G-BDOF, request QDM, G-BDOF”
The operator replies with the bearing and its class:
“G-BDOF, QDM 205, class Bravo”
Repeating the Q code and call sign gives the operator time to read the bearing.
The bearing comes from your transmission, so keep the aircraft straight and level while you talk.
Chapter 6 · VHF Direction Finder
06
e-books by eatpl.in · © 2026 · Do not copy or distribute
To get a bearing, call on the station's frequency: QDM QDM QDM, Oxford Approach, G-BDOF, request QDM, G-BDOF. The repetition gives the operator time to read the bearing from your transmission. The reply gives the bearing and its class, for example QDM 205, class Bravo. Straight and level gives the best result, because the system is vertically polarised.
02
The bearings Four Q codes, two references, two directions; and how good each bearing is.
e-books by eatpl.in · © 2026 · Do not copy or distribute
The service provided
Four Q codes Code Meaning Use QDM Magnetic heading to steer to the station, zero wind Homing, let-downs QDR Magnetic bearing from the station En route QTE True bearing from the station En route, plotting QUJ True track to the station Rarely used
QDM = QDR ± 180 · QUJ = QTE ± 180 · mag = true − east variation
True N Mag N QDR 110 (mag) QTE 100 (true) QDM 290 (mag) to steer back QUJ 280 (true track to station) VDF station variation 10°W: mag = true + 10
Chapter 6 · VHF Direction Finder
08
e-books by eatpl.in · © 2026 · Do not copy or distribute
Four bearings. QDM is the magnetic heading to steer in zero wind to reach the station; it's used for homing and let-downs. QDR is the aircraft's magnetic bearing from the station; QTE its true bearing from the station; both used en route. QUJ is the true track to the station, and isn't generally used. QDM is the reciprocal of QDR; QUJ is the reciprocal of QTE. In the diagram, variation is 10 west: the aircraft bears 110 magnetic, 100 true from the station; to return it steers QDM 290, a true track of 280.
Working with the codes
Convert through true and magnetic, from and to Start from what you're given: is it true or magnetic , from or to ? True ↔ magnetic: variation east, magnetic least ; variation west, magnetic best From ↔ to: add or subtract 180° The class (accuracy) stays with every converted bearing Given QTE 353°, var 8°E, class B QTE (true from) 353° ± 5° QDR (mag from) = 353 − 8 345° ± 5° QDM (mag to) = 345 − 180 165° ± 5° QUJ (true to) = 353 − 180 173° ± 5°
Chapter 6 · VHF Direction Finder
09
e-books by eatpl.in · © 2026 · Do not copy or distribute
Converting is two separate steps. True to magnetic uses variation: variation east, magnetic least, so subtract easterly variation; add westerly. From to to adds or subtracts 180. Given a true bearing of 353, variation 8 east, class B: QTE 353 plus or minus 5; QDR 345; QDM 165; QUJ 173. The class applies to every one of them. That's exam question 5: the correct option is QTE 353 plus or minus 5.
Use of the service
Check track, fix, home, let down QTE or QDR : check you're tracking towards or away from a station; an en-route position line Two stations' bearings give a fix QDM : home to the station; let down in cloud with a published procedureATC: identify an aircraft on radar Station 1: QTE Station 2: QTE
Chapter 6 · VHF Direction Finder
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
QTE or QDR let you check you're on a true or magnetic track from a VDF station, and give a position line en route; two stations give a fix. QDM is for homing to the station and for let-downs through cloud using published procedures. ATC can also use VDF to identify an aircraft on radar. The diagram shows the class B fans from two stations overlapping: the fix is somewhere in that overlap.
Classification of bearings
How good is the bearing? Class Accuracy A within ±2° B within ±5° C within ±10° D worse than ±10°
Bearings are given only when conditions are satisfactory, and normally no better than class B . A bearing passed without a class : assume ±5° .
A ±2° B ±5° C ±10° D >10° At 100 nm, ±5° is about ±9 nm
Chapter 6 · VHF Direction Finder
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
The operator assesses each bearing and passes a class: A within 2 degrees, B within 5, C within 10, D worse than 10. Bearings are only given when conditions are satisfactory, and normally nothing better than class B is available, so a QDM given without a classification can be taken as accurate to within 5 degrees. Remember angular error grows with range: at 100 nautical miles, 5 degrees is about 9 miles either side.
03
Range, accuracy and services Line of sight, what spoils a bearing, emergency fixing and let-downs.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Range of VDF
Line of sight: 1.25 (√h₁ + √h₂) VHF and UHF: range by line of sight ; higher aircraft and aerials see further High ground cuts range, especially for low aircraft in hillsTransmitter power at both ends limits range Temperature and humidity gradients (ducting ) can give more than line of sight Two aircraft transmitting together: momentary bearing errors h₂ station h₁ aircraft range (nm) = 1.25 (√h₁ + √h₂), heights in feet9000 ft aircraft, 400 ft station: 1.25 × (94.9 + 20) = 143 nm
Chapter 6 · VHF Direction Finder
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
VDF uses VHF, or UHF, so range follows line of sight: range in nautical miles is 1.25 times the sum of the square roots of the two heights in feet. Intervening high ground limits range, especially for low-flying aircraft in hilly terrain; transmitter power at both ends limits it; and temperature and humidity gradients can duct signals beyond line of sight. Synchronous transmissions from two aircraft cause momentary errors. Example: an aircraft at 9000 feet and a station at 400 feet: root 9000 is 94.9, root 400 is 20; 1.25 times 114.9 is 143 nautical miles.
Factors affecting accuracy
What spoils a bearing
Site and propagation error The signal reflects off terrain on the way, or off buildings at the site.
Aircraft attitude VDF and VHF comms are vertically polarised: fly straight and level while transmitting.
Overhead the station Poor accuracy near overhead, especially with modern Doppler DF.
Multipath and fading Direct plus ground-reflected waves cause brief fading or loss and bearing errors.
Chapter 6 · VHF Direction Finder
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
Four things degrade a bearing. Propagation and site error: the signal reflects off terrain en route, or off buildings at the site. Aircraft attitude: the system is vertically polarised, so best results come straight and level. Overhead the station accuracy is poor, particularly with Doppler equipment. And the direct and ground-reflected waves together cause short-lived fading and, with other multipath signals, bearing errors.
VHF emergency service
Auto-triangulation on 121.5 MHz UK: 16 outstations fix aircraft on 121.5 MHz (VHF) and 243.0 MHz (UHF) For pilots in distress , in urgent need of help, or in difficulty (lost) VHF: 3000 ft and above in the London FIR; 2000 ft and above in the London area Elsewhere: the D & D cell plots outstation bearings by hand UHF 243.0 MHz: throughout the UK, for the military MAYDAY on 121.5 MHz Bearings from several outstations fix the aircraft
Chapter 6 · VHF Direction Finder
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
In the UK, as described, 16 outstations provide an auto-triangulation fixing service on the VHF emergency frequency, 121.5, and the UHF emergency frequency, 243.0, for pilots in distress, in urgent need of help, or in difficulty, such as lost. On VHF it's available at 3000 feet and above in the London FIR, 2000 feet and above in the London area. Elsewhere the Distress and Diversion cell plots bearings from outstations by hand. The UHF service covers the whole UK for the military. Check the current AIP for today's arrangements.
VHF let-down service
QDM or QGH QDM procedure QGH procedure Who takes the bearings Pilot asks for a series of QDMs Controller takes them Who interprets Pilot : own headings and heightsController : passes headings and heightsWhere Normal at civil aerodromes Only for specific operational reasons
VDF / aerodrome outbound: QDR, descending inbound: QDM to the field QDM: pilot interprets · QGH: controller interprets
Chapter 6 · VHF Direction Finder
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
Two VDF let-down procedures. In a QDM procedure the pilot asks for a series of QDMs and uses them to fly the published pattern, adjusting heading and height. In a QGH, the controller takes the bearings, interprets them and passes headings and heights to keep the aircraft in the pattern. Civil aerodromes normally offer only the QDM procedure; QGH only where there's a specific operational reason.
Summary
What to take into the exam Equipment Ground: Adcock aerial, CRT (CRDF); Doppler DF ±0.5°. Aircraft: just its VHF.
Bearings QDM mag to · QDR mag from · QTE true from · QUJ true to.
Uses Check track, position line, two-station fix, homing, let-downs.
Classes A ±2 · B ±5 · C ±10 · D >10. Normally no better than B; unclassified: ±5.
Range 1.25 (√h₁ + √h₂); terrain, power, ducting. Accuracy: site, attitude, overhead, multipath.
Services Emergency auto-triangulation (121.5 / 243.0). Let-down: QDM pilot, QGH controller.
Chapter 6 · VHF Direction Finder
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
Six points: ground equipment and Doppler DF accuracy; the four Q codes; their uses; the classes, with B the usual best and the assumption for an unclassified bearing; range and accuracy factors; and the emergency and let-down services.
Practice · Questions
Try these 1. A VHF station at 2500 ft amsl, 300 nm away. Lowest altitude for contact? (a) 190 ft (b) 1378 ft (c) 36 100 ft (d) 84 100 ft
2. Class B VDF bearings are accurate to within: (a) ±1° (b) ±5° (c) ±2° (d) ±10°
3. A QDM given without a classification may be assumed accurate to within: (a) 2° (b) 5° (c) 7.5° (d) 10°
4. Aircraft at 9000 ft, VDF station at 400 ft amsl. Maximum range? (a) 115 nm (b) 400 nm (c) 143 nm (d) 63.5 nm
5. A true bearing from a VDF of 353°, variation 8°E, class B: (a) QDM 345 ±5 (b) QDR 345 ±2 (c) QTE 353 ±5 (d) QUJ 353 ±2
6. Aircraft at 19 000 ft, VDF station at 1400 ft amsl. Maximum range? (a) 175 nm (b) 400 nm (c) 62.5 nm (d) 219 nm
Chapter 6 · VHF Direction Finder
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
Six questions from the chapter's paper. Answers on the next slide; all of them can be set up in the VDF Lab.
Practice · Answers
Answers and working Q Answer Working 1 (c) 36 100 ft 300 ÷ 1.25 = 240; √2500 = 50; √h = 190; h = 36 100 2 (b) ±5° Class B 3 (b) 5° Normally no better than class B 4 (c) 143 nm 1.25 × (√9000 + √400) = 1.25 × (94.9 + 20) 5 (c) QTE 353 ±5 QDR 345, QDM 165, QUJ 173, all ±5 6 (d) 219 nm 1.25 × (√19 000 + √1400) = 1.25 × (137.8 + 37.4)
Chapter 6 · VHF Direction Finder
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
Question 1 works backwards: 300 over 1.25 is 240; take off root 2500, which is 50, leaving 190; squared, 36 100 feet. Question 5: the true bearing from the station is the QTE, 353, and class B means plus or minus 5. The other options have the wrong value or the wrong class.
Drag an aircraft round a VDF station: QDM, QDR, QTE, QUJ live See the class fan and a two-station fix Home on QDM in a crosswind and watch the curve Line-of-sight range, both ways Exam questions ready to set up Open the VDF Lab →
QDM 220 · QDR 040
Chapter 6 · VHF Direction Finder
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
The VDF Lab puts an aircraft round a VDF station: drag it and read all four bearings with their class, add a second station for a fix, home on QDM with wind, and work out VHF range.
eatpl.in · Radio Navigation · Chapter 6
VDF Lab
Drag an aircraft round a VDF station and read its four bearings, home on QDM in a crosswind, and work out VHF range.
Bearings Homing Range Practice
Questions from the chapter's paper, plus two lab exercises. Set each one up, read the answer, then open the working.
E-book and lab by eatpl.in · © 2026 eatpl.in. For the personal study of eatpl.in students. Do not copy or distribute.