N E S W 070 RADIALRadio Navigation · Chapter 8
VHF Omni-Directional Range (VOR) How a VOR beacon gives every aircraft its magnetic bearing, what limits its range and accuracy, and how to read it on the CDI and RMI.
© 2026 eatpl.in. All rights reserved. For the personal study of eatpl.in students only. No part may be copied, reproduced, shared or distributed in any form without prior written permission. Unauthorised use may attract civil and criminal liability under the Copyright Act, 1957.
e-books by eatpl.in · © 2026 · Do not copy or distribute
VOR is the backbone short-range aid: airways, holds, let-downs and en-route fixes all hang off it. This chapter covers how the beacon encodes bearing, the ground station details the exam loves (frequencies, monitoring, DOC, range formula, errors), and then the cockpit side: the deviation indicator, the RMI and the in-flight procedures.
Chapter roadmap
What this chapter covers 01
How VOR works Phase comparison of two 30 Hz signals, radials, QDR and QDM.
02
The ground station Frequencies, ident, monitoring, types, range, DOC, errors, the cone of ambiguity and Doppler VOR.
03
In the cockpit The deviation indicator, TO/FROM, the RMI, in-flight procedures and airway geometry.
Chapter 8 · VHF Omni-Directional Range (VOR)
02
e-books by eatpl.in · © 2026 · Do not copy or distribute
Three parts. First the principle: how a beacon can tell every aircraft its own magnetic bearing at once. Then the ground station and everything that limits range and accuracy. Then the cockpit: reading the CDI and RMI, and flying interceptions, track-keeping and station passage. Practice questions and the VOR Lab at the end.
01
How VOR works A VOR measures one thing: the phase difference between two 30 Hz signals. That difference is your radial.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Part one: the principle of operation.
Introduction
The standard short-range aid Adopted by ICAO as the standard short-range aid in 1960 360 radials at 1° spacing, referenced to magnetic north at the VOR VHF, so practically free of static and no sky-wave : usable day and night Paired with a co-located DME it gives an instant range and bearing (rho-theta ) fix Frequency band 108–117.95 MHz
Airways Marks the start, end and centre line of airways and airway sections.
Let-downs Approach aid at airfields using published procedures.
Holding A holding point for aircraft.
En-route A source of en-route position lines.
Chapter 8 · VHF Omni-Directional Range (VOR)
04
e-books by eatpl.in · © 2026 · Do not copy or distribute
The VHF Omni-directional Range was adopted by ICAO in 1960. It produces 360 radials at one degree spacing, aligned to magnetic north at the beacon. Because it is VHF it is practically free from static and is not affected by sky-waves, so it can be used day and night. Pair it with a DME and you get an instantaneous range and bearing fix, called rho-theta. Its four uses: defining airways, let-downs at airfields, holding points, and en-route position lines.
The principle of operation
Bearing by phase comparison Reference signal: 30 Hz, FM , omnidirectional, so its phase is the same everywhereVariable signal: 30 Hz, AM , made by a limaçon pattern rotating 30 times a secondThe two are in phase due magnetic north of the beacon Anywhere else, the phase difference = your magnetic bearing from the VOR Different modulations stop the two 30 Hz signals interfering in the receiver.
090° phase difference Reference 30 Hz · FM · same phase in every direction Variable 30 Hz · AM · rotating limaçon
Chapter 8 · VHF Omni-Directional Range (VOR)
05
e-books by eatpl.in · © 2026 · Do not copy or distribute
The aircraft's receiver compares two 30 hertz signals. The reference is frequency modulated and radiated equally in all directions, so its phase does not depend on where you are. The variable signal is amplitude modulated by a limacon-shaped pattern that rotates 30 times a second, so the moment its peak reaches you depends on your bearing. They are synchronised to be in phase due magnetic north. The phase difference you measure is your magnetic bearing from the beacon: here 90 degrees, so the 090 radial. Early VORs rotated the pattern mechanically; modern ones do it electronically.
30 rev/s 000° 090° 180° 270°Phase differences
Phase difference equals radial Measured phase Radial 000° 000 (due north) 090° 090 (east) 227° 227 314° 314
A VOR transmits all 360 radials continuously, and bearing information keeps coming even during the identification.
Chapter 8 · VHF Omni-Directional Range (VOR)
06
e-books by eatpl.in · © 2026 · Do not copy or distribute
One revolution of the limacon with the phase difference at the four cardinal points: zero due north, 90 east, 180 south, 270 west. The rule is simply that the phase difference measured at the aircraft is the radial. 227 degrees of phase is the 227 radial; 314 is the 314 radial. Bearing information is supplied all the time, even while the ident is being sent.
Terminology
Radials are bearings FROM the beacon
Radial = QDR Magnetic bearing from the VOR to the aircraft.
QDM Magnetic bearing to the VOR. QDM = radial ± 180°.
Radials use magnetic north at the beacon , not at the aircraft Tracking between two VORs: fly FROM the first, then change to TO the next at the mid or transfer point N(M) 070 radial (QDR 070) 70° QDM 250 (bearing TO) VOR
Chapter 8 · VHF Omni-Directional Range (VOR)
07
e-books by eatpl.in · © 2026 · Do not copy or distribute
A radial is a magnetic bearing from the VOR, which is the same thing as a QDR. The QDM is the magnetic bearing to the beacon, the reciprocal. An aircraft on the 070 radial has a QDM of 250. Because the VOR builds its radials around magnetic north at its own position, any conversion to true uses the variation at the beacon. On an airway between two VORs, you track outbound from the first, FROM indication, and change over to the second, TO indication, at the midpoint or the published transfer point.
02
The ground station Frequencies, identification, monitoring, range, protection and the errors that limit accuracy.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Part two: the beacon itself and what limits it.
Transmission details
108 to 117.95 MHz, 160 channels
108–112 MHz · 40 channels Mainly an ILS band, shared with short-range and terminal VORs. VORs use an even first decimal: 108.00, 108.05, 108.20, 108.25 … 111.85.
112–117.95 MHz · 120 channels The en-route VOR band. 40 + 120 = 160 VOR channels in total.
Emission A9W A amplitude-modulated double side-band carrier · 9 composite system · W telemetry, telephony and telegraphy combined.
Chapter 8 · VHF Omni-Directional Range (VOR)
09
e-books by eatpl.in · © 2026 · Do not copy or distribute
VOR sits in the VHF band between 108 and 117.95 megahertz. 108 to 112 is primarily the ILS band but is shared with short-range and terminal VORs; VOR frequencies there have an even first decimal, so 108.0, 108.05, 108.2, 108.25 and so on, while ILS localisers take the odd ones. 112 to 117.95 gives another 120 channels, 160 in all. The emission designator is A9W: amplitude modulated double side-band main carrier, composite system, and a combination of telemetry, telephony and telegraphy.
Identification and monitoring
No ident, no use Identification 3-letter Morse , about 7 groups a minute, at least every 10 s May also be voice (“This is Miami Omni”), then the Morse Voice channel can carry ATIS (AM), sent with the bearing information Test VOR (VOT ): continuous tone or a series of dots Automatic site monitor Removes ident and navigation signals, or switches off, if: bearing shifts by more than 1° either 30 Hz modulation or the carrier drops by more than 15% the monitor itself fails Standby changeover: bearings may be wrong and no ident is sent. Ident TST = on test. Do not use either.
Chapter 8 · VHF Omni-Directional Range (VOR)
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
UK VORs identify with three-letter Morse at about seven groups a minute, at least every ten seconds. Some add a voice ident, and the voice channel can carry ATIS using AM at the same time as the bearing signals. A test VOR identifies with a continuous tone or dots. Every VOR has an automatic site monitor. It warns the control point and removes the ident and navigation signals, or switches off, if the bearing shifts more than one degree, if either 30 hertz modulation or the carrier drops more than 15 percent, or if the monitor fails. When the standby transmitter comes on it takes time to stabilise, bearings may be wrong and no ident is sent. So never use a VOR without its ident, and never use one identifying TST.
Types of VOR
Six names to recognise Type What it is BVOR Broadcast VOR: weather and airfield information between idents DVOR Doppler VOR: overcomes site error TVOR Terminal VOR: low power, at major airfields VOT Test VOR: one omnidirectional test radial (360) for checking aircraft equipment before IFR flight; more than ±4° error needs servicing VORTAC VOR co-located with TACAN (whose DME civil aircraft can use) DBVORTAC A combination of the above: Doppler, broadcast, VOR and TACAN
Chapter 8 · VHF Omni-Directional Range (VOR)
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
Six types. A broadcast VOR gives weather and airfield information between idents. A Doppler VOR overcomes siting errors. A terminal VOR is low power, used at major airfields. A VOT, found at some airfields, broadcasts a single omnidirectional test signal so you can check your receiver before IFR flight; an error of more than plus or minus 4 degrees means the equipment needs servicing. A VORTAC is a VOR with a co-located TACAN, whose DME function civil aircraft use. DBVORTAC is the combination.
Operational range
Line of sight, set by power and height Power: en-route 200 W ≈ 200 nm; a TVOR about 50 WHeight of transmitter and receiver: line of sight plus a little refractionTerrain screens, reflects or bends (scallops) the signal; known errors appear in the AIPRange (nm) = 1.25 × (√H1 + √H2) · heights in feet amsl
FL360 and a beacon at 900 ft: 1.25 × (√36,000 + √900) = 1.25 × (189.7 + 30) ≈ 274 nm
Aircraft (H1) VOR (H2) line of sight Earth
Chapter 8 · VHF Omni-Directional Range (VOR)
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
Range depends first on power: a 200 watt en-route VOR gives about 200 nautical miles, a terminal VOR transmits about 50 watts. Then height, because VHF is line of sight with a small bonus from atmospheric refraction. The exam formula is 1.25 times the sum of the square roots of the two heights in feet. At flight level 360 with the beacon at 900 feet: root 36,000 is 189.7, root 900 is 30, total 219.7, times 1.25 is about 274 nautical miles. Terrain also matters: it can stop, reflect or bend the signal, and published errors look like errors up to five and a half degrees in sector 315 to 345 out to 40 nautical miles.
Designated operational coverage
Protection from beacons on the same frequency Only 160 channels worldwide, so frequencies are reused Line of sight at 25,000 ft is 1.25 × √25,000 ≈ 198 nm , so co-channel beacons need ≥ 396 nm ; planners use about 500 nm DOC 50/25 : no co-channel interference within 50 nm up to 25,000 ft Valid day and night ; may vary by sector. Outside the DOC, expect errors VOR 2 · DOC 100/50 VOR 1 · DOC 50/25 50 nm 25,000 ft
Chapter 8 · VHF Omni-Directional Range (VOR)
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
With only 160 frequencies worldwide they must be reused, and two beacons on the same frequency must be far enough apart not to interfere. At 25,000 feet line of sight is about 198 nautical miles, so twice that is 396, and planners add about 100 to make it roughly 500. In practice a beacon is protected only as far as it needs to be, and that protection is published as the designated operational coverage: a range and a height. DOC 50 slash 25 means no co-frequency interference within 50 nautical miles up to 25,000 feet. It applies day and night and may vary by sector. Use outside the DOC can lead to navigation errors.
Factors affecting accuracy
Errors add up to about ±5°
Site error Terrain, buildings, trees, even long grass near the beacon. Monitored to ±1° . Called VOR course-displacement error.
Propagation error Terrain and distance bend the radials far from the beacon: scalloping , the CDI drifting or jumping side to side.
Airborne equipment Converting phase difference to bearing. Maximum ±3° .
Total ±5° aggregate. Add pilotage error : near the beacon the radials crowd together.
Chapter 8 · VHF Omni-Directional Range (VOR)
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
Site error comes from uneven terrain and obstructions near the transmitter, even trees and long grass; it is monitored to plus or minus one degree. Propagation error happens after the signal leaves the site: terrain and distance cause bends or scalloping, an imperfection in the received signal that makes the CDI move slowly or rapidly from side to side. Airborne equipment error, converting phase difference to bearing, should be no more than three degrees. The aggregate is plus or minus five degrees, which is the figure to use in airway questions. On top of that is pilotage error: close to the beacon the one degree radials are very close together.
Station passage
The cone of ambiguity No planned radiation straight up, so near the overhead the radials converge and the needle becomes very sensitive Needle swings, OFF flag may appear, TO/FROM alternates ICAO coverage to at least 40° elevation; in practice 60–80° At high level the cone is wide: about 4 nm radius at 30,000 ft Readings settle once you are through it cone of ambiguity TO FROM needle swings · OFF flag 60–80° in practice (ICAO minimum 40°)
Chapter 8 · VHF Omni-Directional Range (VOR)
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
There is no planned radiation straight up from a VOR, so overhead there is a cone of ambiguity, or confusion. As you approach, the radials converge and the needle becomes more sensitive; near the overhead it oscillates, the OFF flag may appear briefly and the TO-FROM display alternates. ICAO requires usable signals up to at least 40 degrees elevation; modern beacons manage 60 to 80. At high level the cone covers a large area, about 4 nautical miles radius at 30,000 feet, so station passage is slow up there and quick at low level. Once through, the readings settle.
Doppler VOR (DVOR)
Second generation: less site error Conventional VOR (CVOR) Doppler VOR (DVOR) Reference 30 Hz FM AM Variable 30 Hz AM FM Rotation of the variable signal Clockwise Anticlockwise (simulated)Site error Larger Smaller , so more accurateFrequencies, airborne receiver Same Same
Swapping the modulations and reversing the rotation keeps the phase relationship, so the pilot cannot tell from the instruments which type is in use.
Chapter 8 · VHF Omni-Directional Range (VOR)
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
The Doppler VOR is the second generation. Same frequencies, but better bearing accuracy because it is much less sensitive to site error. Its reference signal is AM and its variable signal is FM, the opposite of a conventional VOR, and the apparent rotation is anticlockwise. Those two changes cancel out so the same airborne equipment works with either, and there is no way of telling from the display which type you are using. Exam favourite: in a DVOR the reference is AM, the bearing signal FM, rotation anticlockwise.
03
In the cockpit The deviation indicator shows where you are relative to a selected track; the RMI shows the bearing.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Part three: the airborne equipment and how to fly with it.
VOR airborne equipment
Three parts on board
01
Aerial A whip on the fuselage for slower aircraft; a blade or flush aerial on either side of the fin for fast ones.
02
Receiver A box in the avionics bay that measures the phase difference.
03
Indicator Feeds a flight director, or simpler displays: the CDI (course deviation indicator) and the RMI (radio magnetic indicator).
Chapter 8 · VHF Omni-Directional Range (VOR)
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
Three components. The aerial: a whip on slower aircraft, a blade or flush-mounted aerial on the fin for high-speed aircraft. The receiver, in the avionics bay. And the indicator: the output can drive a flight director or the simpler displays, the course deviation indicator and the radio magnetic indicator, which are the next slides.
VOR / ILS deviation indicator
Displacement from the track you select Turn the OBS knob to select a bearing; the needle shows how far you are from it 5-dot scale : the circle is the first dot, each dot ≈ 2° , full scale 10° In the ILS role each dot is only ½°, full scale 2½° Heading has no effect on the display: only position and the selected bearingOFF flag: faulty signal, out of range, or no power FROM 080 OBS
Chapter 8 · VHF Omni-Directional Range (VOR)
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
The deviation indicator, also called the omni bearing indicator, shows the aircraft's displacement from a bearing the pilot selects with the omni bearing selector. On a typical five-dot display the circle counts as the first dot and each dot is about 2 degrees, so full-scale deflection is 10 degrees. In the ILS role each dot is only half a degree. The key point: the indication depends only on where the aircraft is and what bearing is selected. Heading does not affect it. Here 080 is selected, the flag shows FROM and the needle is two and a half dots, 5 degrees, to the left. The OFF flag appears if the signal is faulty, you are out of range or the power supply is inadequate.
TO / FROM and needle sense
Select the track you are flying TO when your QDM is within about 80° of the selected bearingFROM when your QDR (radial) is within about 80° of itTwo indeterminate sectors about 20° wide in between Inbound: set the inbound track, see TO . Outbound: set the outbound track, see FROM . Heading ≈ selected track keeps the needle sense correct: fly towards the needle .
080 selected FROM TO ? ? N
Chapter 8 · VHF Omni-Directional Range (VOR)
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
The TO-FROM flag works on position too. TO appears when your QDM is within about 80 degrees of the selected bearing, FROM when your radial is within about 80 degrees, leaving two indeterminate sectors of about 20 degrees. Needle sense is correct, meaning you fly towards the needle, only when your heading is roughly the selected track. If you are inbound but have the outbound track selected, the needle is reversed: that was aircraft 4 in the figure, showing fly left when it actually needs to turn right. So the rule: inbound, set the inbound track and see TO; outbound, set the outbound track and see FROM.
Radio magnetic indicator (RMI)
Head shows QDM, tail shows the radial Compass card driven by a remote compass: magnetic heading at the index Needle head = QDM to the beacon; tail = radial (QDR) A differential synchro subtracts heading from QDM to drive the needle, and the card adds it back For true bearings apply variation at the VOR (ADF: at the aircraft) Heading 040°(M), phase difference 270° → QDM 090. Needle 50° right of the index points to 090 ; tail reads 270 radial .
N 3 6 E 12 15 S 21 24 W 30 33
Chapter 8 · VHF Omni-Directional Range (VOR)
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
The RMI has a compass card driven by a remote-reading compass, so magnetic heading sits under the index at the top. The needle head shows the QDM to the beacon and the tail shows the reciprocal, the radial you are on. Inside, the VOR QDM from the phase difference has the heading subtracted by a differential synchro to give a relative bearing, which positions the needle, and the card puts the heading back. Example: heading 040, phase difference 270 means radial 270, QDM 090, relative bearing 050; the needle sits 50 degrees right of the index and points at 090. Because a VOR bearing is based on the magnetic meridian at the beacon, convert to true using variation at the VOR. For an ADF on the RMI you use variation at the aircraft.
RMI versus deviation indicator
Heavier and costlier, but worth it QDM and radial Continuous QDM at the head and radial at the tail.
Heading too Magnetic heading on the same instrument: ideal for homing and tracking outbound.
Plan view The relative bearing is obvious at a glance, which helps in a hold.
Interceptions The rate of crossing radials is easy to judge.
Two needles One beacon ahead or astern for tracking, another off the airway for the abeam report.
ADF as well ADF bearings can be shown on the same RMI.
Chapter 8 · VHF Omni-Directional Range (VOR)
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
The RMI needs a remote compass and power supplies, so it is heavier, bigger and dearer than a deviation indicator. In large aircraft that is outweighed by six advantages: continuous QDM and radial; magnetic heading on the same instrument; a plan view of the situation that is especially useful in the hold; easy judgement of the rate of crossing radials when intercepting; two needles for two beacons, typically one for track-keeping and one for the abeam position report; and ADF bearings on the same display.
In-flight procedures
Intercept, track, pass the station Intercept the 280 radial on heading 045, turning early: at the 277 radial the CDI shows about 1½ dots fly left and the RMI reads QDM 097Track inbound on 090 for 10° drift. Needle drifting left? Alter 30° to 060 until it centres, then try 085Station passage : needle swings, OFF may show, TO changes to FROM, RMI swings through 180°Outbound on the 150 radial: FROM, needle central, RMI tail on 150 (head on QDM 330) 280 radial · inbound track 100 150 radial outbound FROM · RMI head 330 HDG 045 HDG 090 (10° drift) RMI: QDM 100 N(M)
Chapter 8 · VHF Omni-Directional Range (VOR)
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
A worked flight. The aircraft intercepts the 280 radial, inbound track 100, flying heading 045. It plans to turn onto heading 090 to allow for starboard drift, a 45 degree turn taking about 15 seconds, so it starts the turn early: at the 277 radial the CDI shows about one and a half dots fly left and the RMI reads QDM 097. Inbound, if the needle drifts progressively left the aircraft is right of track and the drift allowance is too small: turn 30 degrees port to 060 until the needle centres, then try 085. Over the beacon the needle swings, OFF may appear, TO changes to FROM and the RMI needle rotates through 180 degrees, quickly at low level, slowly at high level. Outbound on the 150 radial the flag shows FROM, the needle is central and the RMI head shows QDM 330.
Using the 1 in 60 rule
Dots, degrees and miles off track Dots × 2 = degrees off the selected radial Miles off track = range × degrees ÷ 60 UK airway: centre line ± 5 nm . With ±5° error, the edge is reached at 60 nm, so beacons up to 120 nm apart Homing on the 064 radial, 4 dots fly right with TO, DME 45 nm: 8° × 45 ÷ 60 = 6 nm left of track .
On the airway edge 100 nm out: 5 × 60 ÷ 100 = 3° = 1½ dots .
60 nm 5° airway edge · 5 nm centre line VOR (width exaggerated)
Chapter 8 · VHF Omni-Directional Range (VOR)
24
e-books by eatpl.in · © 2026 · Do not copy or distribute
Many VOR questions are really 1 in 60 questions. Dots times two gives degrees; degrees times range over 60 gives miles off track. A UK airway extends 5 nautical miles either side of the centre line. If the maximum VOR error is 5 degrees, an aircraft reaches the edge 60 nautical miles from the beacon, so beacons can be up to 120 apart with the changeover at the midpoint; with 5.5 degrees it is 54.5 and 109. Homing on the 064 radial with 4 dots fly right and TO: 8 degrees at 45 miles is 6 miles, and a fly-right needle means the track is to your right, so you are 6 miles left of track. On the boundary at 100 miles: 5 miles is 3 degrees, one and a half dots.
Summary
What to take into the exam Principle Phase difference of two 30 Hz signals = radial. CVOR: reference FM, variable AM, clockwise. DVOR: reference AM, variable FM, anticlockwise.
Frequencies 108–117.95 MHz, 160 channels, A9W. Even first decimal in 108–112 (shared with ILS).
Ident and monitor 3-letter Morse every 10 s. Monitor trips at 1° shift or 15% drop. No ident or TST: don't use.
Range 1.25 × (√H1 + √H2). DOC = range/height free of co-channel interference, day and night.
Accuracy Site ±1°, equipment ±3°, total ±5°. Scalloping from reflections. Cone of ambiguity overhead.
Displays CDI 2° per dot, 10° full scale, heading-independent. RMI head QDM, tail radial; variation at the VOR.
Chapter 8 · VHF Omni-Directional Range (VOR)
25
e-books by eatpl.in · © 2026 · Do not copy or distribute
The six things to carry into the exam. The principle, including the CVOR and DVOR modulations and rotation. The frequency band and A9W. The ident and monitoring rules. The range formula and the meaning of DOC. The error budget, scalloping and the cone of ambiguity. And the two displays: CDI two degrees per dot and independent of heading; RMI head QDM, tail radial, with variation applied at the VOR.
Practice · Questions
Try these 1. Theoretical maximum range from a VOR at 900 ft amsl for an aircraft at FL360? (a) 274 nm (b) 255 nm (c) 112 nm (d) 224 nm
2. OBS set to 330, 3 dots fly right, FROM. What is the aircraft's QDM to the station? (a) 144 (b) 324 (c) 336 (d) 156
3. Homing to a VOR on the 064 radial: CDI 4 dots fly right with TO, DME 45 nm. Where is the aircraft? (a) 6 nm right (b) 3 nm right (c) 6 nm left (d) 3 nm left of track
4. To intercept and home along the 064 radial, set the OBS to: (a) 064, TO (b) 244, TO (c) 064, FROM (d) 244, FROM
5. Tracking away from a VOR, heading 287°(M) with 14° starboard drift, variation 6°W. Phase difference? (a) 121° (b) 295° (c) 301° (d) 315°
6. Maximum VOR error 5.5°. How far apart can beacons on a UK airway centre line be? (a) 54.5 nm (b) 109 nm (c) 66 nm (d) 132 nm
Chapter 8 · VHF Omni-Directional Range (VOR)
26
e-books by eatpl.in · © 2026 · Do not copy or distribute
Six of the end-of-chapter questions, lightly reworded. Answers and working on the next slide. All of them can be set up in the VOR Lab.
Practice · Answers
Answers and working Q Answer Working 1 (a) 274 nm 1.25 × (√36,000 + √900) = 1.25 × 219.7 2 (a) 144 FROM, needle right of 330 → on the 324 radial; QDM = 324 − 180 3 (c) 6 nm left 4 dots = 8°; 45 × 8 ÷ 60 = 6 nm; track is to the right 4 (b) 244, TO Inbound on the 064 radial means track 244: select 244 for TO and correct sense 5 (c) 301° Track = 287 + 14 = 301°(M) = radial 301; variation is irrelevant 6 (b) 109 nm 5 nm at 5.5°: 5 × 60 ÷ 5.5 = 54.5 nm each side of the midpoint
Chapter 8 · VHF Omni-Directional Range (VOR)
27
e-books by eatpl.in · © 2026 · Do not copy or distribute
Question 2: FROM with 330 set means you are near the 330 radial; fly right means the course is to your right as you fly outbound, so you are anticlockwise of it, on the 324 radial, and the QDM is 144. Question 3: a fly-right needle with TO means the inbound track lies to the right, so you are left of it. Question 5: radials are magnetic, so the track 301 magnetic is the radial and the phase difference; the variation is a distractor.
Drag the aircraft round a VOR and watch the CDI and RMI respond Turn the OBS and heading: see TO/FROM, needle sense and the cone of ambiguity Work out line-of-sight range and check a DOC Exam questions ready to set up Open the VOR Lab →
TO 244 OBS N 3 6 E 12 15 S 21 24 W 30 33
Chapter 8 · VHF Omni-Directional Range (VOR)
28
e-books by eatpl.in · © 2026 · Do not copy or distribute
The VOR Lab puts a VOR on a moving map with a live CDI and RMI. Students can drag the aircraft, set the OBS and heading, see the TO-FROM sectors and needle sense, fly through the cone of ambiguity, and work the range and airway questions.
eatpl.in · Radio Navigation · Chapter 8
VOR Lab
Drag the aircraft anywhere round the VOR. Set the OBS and heading, then press Fly and watch the CDI and RMI.
Fly
Range and 1 in 60
Practice
Fly
Heading = OBS
Centre the needle
Altitude2,000 ft 5,000 ft 10,000 ft FL200 FL300 FL400
Flying runs one minute per second. The VOR is at 500 ft amsl.
Try these
Intercept the 280 radial
Reversed sense
Station passage at FL300
Outbound on the 150
End-of-chapter questions. Set each one up on the map, read the instruments, then open the working.
E-book and lab by eatpl.in · © 2026 eatpl.in. For the personal study of eatpl.in students. Do not copy or distribute.
30 nm 60 nm 120 nm TO/FROM sectors
Selected bearing
FROM sector
TO sector
Cone of ambiguity
Drag the aircraft · map north is magnetic north