ATS SURVEILLANCE

21 questions · tap an answer to check it

Learn this topic firstParallel Runways, SSR and ACASAir Law course →

About this topic

ATS SURVEILLANCE: 21 multiple-choice questions for the DGCA CPL and ATPL examinations. Every question shows the correct answer and an explanation. You can practise free for a few minutes; a subscription opens every question bank, previous paper and airline preparation set.

Sample questions from ATS SURVEILLANCE

  1. The minimum radar separation to be provided to aircraft established on the localizer course shall be:
    • A) 2.0NM between aircraft on adjacent localizer course
    • B) 2.5NM between aircraft on the same localizer course
    • C) 5.0NM between aircraft on the same localizer course
    Show answer

    B) 2.5NM between aircraft on the same localizer course
    ILS Localizer Separation When two (or more) aircraft are established on the same ILS localizer course and are within 10 NM of the runway threshold, the radar separation standard may be reduced to 2.5 NM between the aircraft on the radar display. This reduced separation is allowed under controlled conditions to increase efficiency during approach operations, while still maintaining safety.

  2. Unless otherwise prescribed by the appropriate ATS authority, the horizontal radar separation minimum prescribed by ICAO shall be:
    • A) 3.5NM
    • B) 8 NM
    • C) 5.0NM
    Show answer

    C) 5.0NM
    Standard Horizontal Separation: The general horizontal separation minimum based on radar, ADS-B, or MLAT systems is 9.3 km (5.0 NM). Permissible Reductions in Separation: The radar separation minimum may be reduced by the appropriate ATS authority, but not below: a) 5.6 km (3.0 NM) when radar and/or ADS-B and/or MLAT capabilities at a given location permit. b) 4.6 km (2.5 NM) between succeeding aircraft on the same f

  3. Where ADS-B is used for identification, aircraft may be identified by the following procedure:
    • A) Asking him to sqwuak assigned mode A code C.
    • B) Direct recognition of the aircraft identification in an ADS-B label.
    • C) Recognition of an assigned discrete code, the setting of which has been verified.
    Show answer

    B) Direct recognition of the aircraft identification in an ADS-B label.
    ADS-B Identification Procedures. Where ADS-B is used for identification, aircraft may be identified by one or more of the following procedures: a) direct recognition of the aircraft identification in an ADS-B label; b) transfer of ADS-B identification; c) observation of compliance with an instruction to TRANSMIT ADS-B IDENT;

  4. An aircraft is considered to be maintaining its assigned level as long as the SSR mode C derived level information indicated that it is within:
    • A) +/-500ft of the assigned level in non RVSM airspace
    • B) +/-200ft of the assigned level in RVSM airspace
    • C) +/-300ft of the assigned level in RVSM airspace
    Show answer

    B) +/-200ft of the assigned level in RVSM airspace
    The tolerance value used to determine that pressure-altitude-derived level information displayed to the controller is accurate shall be ±60 m ( 200 ft) in RVSM airspace. In other airspace, it shall be 90 m (300 ft), except that the appropriate ATS authority may specify a smaller criterion, but not less than ±60 m ( 200 ft), if this is found to be more practical. Geometric height information shall not be used for sepa

  5. An aircraft in climb or descent is considered to have crossed a level when the SSR mode C derived level information indicates that it has passed this level in the required direction by:
    • A) +/- 300ft
    • B) More than 300ft
    • C) 300ft
    Show answer

    B) More than 300ft
    Passing a Level with Mode C: Mode C is a transponder feature that provides aircraft altitude information to Air Traffic Control (ATC). When Mode C indicates that an aircraft is within 300 feet of a specified altitude (level) during a climb or descent, it is considered to be passing that level.