OXFORD POF Limitations

13 questions · tap an answer to check it

Learn this topic firstLimitations and the Flight EnvelopePrinciples of Flight course →

About this topic

OXFORD POF Limitations: 13 multiple-choice questions for the DGCA CPL and ATPL examinations. Every question shows the correct answer and an explanation. You can practise free for a few minutes; a subscription opens every question bank, previous paper and airline preparation set.

Sample questions from OXFORD POF Limitations

  1. If an aircraft is flown at its design manoeuvring speed VA:
    • A) it is possible to subject the aircraft to a load greater than its limit load during high 'g' manoeuvres.
    • B) it is only possible to subject the aircraft to a load greater than its limit load during violent increases in incidence, i.e. when using excessive stick force to pull-out of a dive
    • C) it is not possible to exceed the limit load
    • D) it is possible to subject the aircraft to a load greater than its limit load at high TAS
    Show answer

    C) it is not possible to exceed the limit load
    Design manoeuvring speed (VA) is defined as the maximum speed at which the aircraft can sustain full abrupt control deflection without exceeding its limit load factor. At or below VA, the aircraft’s structure is designed so that it will stall before any structural damage due to excessive load occurs. This means that it is not possible to exceed the limit load by using normal or even abrupt control inputs at or below

  2. Maximum structural cruising speed VNO is the maximum speed at which an aeroplane can be operated during:
    • A) normal operations
    • B) abrupt manoeuvres
    • C) flight in smooth air
    • D) flight in rough air
    Show answer

    A) normal operations
    Maximum Structural Cruising Speed (VNO): Definition: The maximum speed at which an aircraft can be safely operated during normal flight conditions (cruise, climb, descent). Purpose: Ensures the aircraft structure is not overstressed under normal turbulence or maneuvers.

  3. The maximum allowable airspeed with flaps extended (V FE) is lower than cruising speed because:
    • A) they are used only when preparing to land
    • B) the additional lift and drag created would overload the wing and flap structure at higher speeds
    • C) flaps will stall if they are deployed at too high an airspeed
    • D) too much drag is induced
    Show answer

    B) the additional lift and drag created would overload the wing and flap structure at higher speeds
    The maximum allowable airspeed with flaps extended (V_FE) is lower than cruising speed because the additional lift and drag created by the flaps at higher speeds could overload the wing and flap structure. Flying faster than V_FE with flaps deployed risks structural damage due to these increased aerodynamic forces.

  4. Why is VLE greater than VLO on the majority of large transport aircraft?
    • A) VLO is used when the aircraft is taking off and landing when the IAS is low.
    • B) extending the gear at too high an airspeed would cause excessive parasite drag
    • C) flying at too high an airspeed with the gear down would prevent retraction of the forward retracting nose gear.
    • D) VLO is a lower IAS because the undercarriage doors are vulnerable to aerodynamic loads when the gear is in transit, up or down.
    Show answer

    D) VLO is a lower IAS because the undercarriage doors are vulnerable to aerodynamic loads when the gear is in transit, up or down.
    On most large transport aircraft, VLE (Maximum Landing Gear Extended Speed) is higher than VLO (Maximum Landing Gear Operating Speed) because: VLO applies when the landing gear is moving (either extending or retracting), and during this time, the undercarriage doors and gear mechanisms are exposed to increased aerodynamic loads and are therefore more vulnerable. To protect these components from damage, VLO is set low

  5. The phenomenon of flutter is described as:
    • A) rapid oscillatory motion involving only rotation of the control surfaces, associated with the shock waves produced around the control surfaces.
    • B) oscillatory motion of part or parts of the aircraft relative to the remainder of the structure
    • C) rapid movement of the airframe caused by vibration from the engines
    • D) reversal of the ailerons caused by wing torsional flexbility
    Show answer

    B) oscillatory motion of part or parts of the aircraft relative to the remainder of the structure
    Flutter is a rapid, self-excited oscillatory motion that involves parts of the aircraft structure (such as control surfaces, wings, or other components) moving relative to the rest of the airframe. This phenomenon arises from an interaction between aerodynamic forces, structural elasticity, and inertial effects. If not controlled, flutter can grow in amplitude and cause structural failure.